Club Cobra GasN Exhaust  

Go Back   Club Cobra > Engine Building, Tuning, and Induction > 429/460 Engine Talk

Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
Keith Craft Racing
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
Keith Craft Racing
Keith Craft Racing
December 2024
S M T W T F S
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31        

Kirkham Motorsports

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #1 (permalink)  
Old 01-16-2007, 10:40 AM
hkelley's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2007
Location: Greensboro NC, NC
Cobra Make, Engine: SPF #2101 Diamond Ed.; 460
Posts: 61
Not Ranked     
Default Looking for Comments on 460 Build and Components

I recently purchased a Superformance with the following engine build. I am looking for info/comments/input as to what is good or bad in this particular build. Thanks in advance.

Joe

460 Cobra Jet Bracket Race SVO
10.5:1 Compression ratio
Edelbrock Performer 460 intake manifold w/Holley 750 CFM
SVO Cobra Jet aluminum heads with SVO valve train M-6049-B429
Polished valves - Intake diameter 2.25" & exhaust diameter 1.76"
SVO high performance hydraulic flat tappet camshaft M-625-C460
Valve lift - .588" intake & .614" exhaust
Duration at .050" is 244 degrees intake & 254 exhaust
SVO 460 2-bolt main short block, oil and water pump, oil pan and harmonic balancer
March polished & clear coated under drive pulleys
MSD 6AL ignition and MAS Blaster 2 coil
Taylor Race 10mm spiral core wires
CSI-106 high torque starter
Aeromotive hi-performance electric fuel pump and pressure regulator
Reply With Quote
  #2 (permalink)  
Old 01-16-2007, 10:46 AM
Ital-cobra's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Aug 2006
Location: Montreal, Canada, QC
Cobra Make, Engine: Emerson cobra, 460 550HP
Posts: 1,093
Not Ranked     
Default

Did you buy all your parts yet? If not I may have some for you new, pistons, intake manifold, etc.

Joseph
__________________
The desire for imaginary benefits often involves the loss of present day blessings.
Reply With Quote
  #3 (permalink)  
Old 01-16-2007, 10:50 AM
hkelley's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2007
Location: Greensboro NC, NC
Cobra Make, Engine: SPF #2101 Diamond Ed.; 460
Posts: 61
Not Ranked     
Default

It is all already there and put together. I bought the car used and am just trying to get feedback on the build that was put together for this car. Thanks.

Joe
Reply With Quote
  #4 (permalink)  
Old 01-16-2007, 11:16 AM
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2005
Location: Bristol, CT
Cobra Make, Engine: Shell Valley 460ci C6
Posts: 22
Not Ranked     
Default

From the part numbers you listed it sounds like you have a Ford crate engine. SVO is now Ford Racing... or someone built it from mostly Ford performance parts. Sounds to be approximately 500 hp...all good parts. All that matters is how does it go...and for how long.
Reply With Quote
  #5 (permalink)  
Old 01-16-2007, 02:49 PM
jdean's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jul 2001
Location: Carrollton, TX
Cobra Make, Engine: JBL now SOLD
Posts: 1,735
Send a message via AIM to jdean
Not Ranked     
Default

With those heads, along with the aggressive cam, you might want to think about a Torker II single plane intake. You should gain some high end power, without giving up much on the bottom....as if you would notice anyway.
__________________
6th generation Texan....
Reply With Quote
  #6 (permalink)  
Old 01-16-2007, 02:52 PM
jdean's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jul 2001
Location: Carrollton, TX
Cobra Make, Engine: JBL now SOLD
Posts: 1,735
Send a message via AIM to jdean
Not Ranked     
Default

Another thing.....the stock SPF exhaust may be choking off some power. You might investigate a larger ID less restrictive muffler.
__________________
6th generation Texan....
Reply With Quote
  #7 (permalink)  
Old 01-16-2007, 04:08 PM
xlr8or's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2001
Location: San Diego, CA
Cobra Make, Engine:
Posts: 2,979
Not Ranked     
Default

The Torker won't fit under the hood of the SPF.
You may benefit on the top end from a slightly larger carb.
You might want to check the rods and see if they are the stock Ford rods or aftermarket.
__________________
Remember, It's never too early to start beefing up your obituary.
Reply With Quote
  #8 (permalink)  
Old 01-16-2007, 06:37 PM
Tom Wells's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Mar 2000
Location: St. Augustine, FL
Cobra Make, Engine: E-M / Power Performance / 521 stroker / Holley HP EFI
Posts: 1,929
Not Ranked     
Default

Hi xlr8or,

I think ya got it backwards. Here are the manifold heights from the Edelbrock web site http://www.edelbrock.com/automotive/...#hoodclearance :

Edelbrock Performer 460 Manifold height: A-3.75", B-4.45" (same as stock)

Edelbrock Torker II 460 Manifold ht.: A-3.50", B-4.25"

As you can see, the Torker is 0.2" shorter in front and 0.25" shorter at the rear.

VOE here (voice of experience), as I stepped in this one when trying to fit my 460 under a decent sized air filter
__________________
Wells's law of engine size: If it matters what gear you're in, the engine's too small!
Reply With Quote
  #9 (permalink)  
Old 01-17-2007, 06:48 AM
hkelley's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2007
Location: Greensboro NC, NC
Cobra Make, Engine: SPF #2101 Diamond Ed.; 460
Posts: 61
Not Ranked     
Default

Thanks everyone for the info. I was also wondering if the airfilter on the car might be too small. I ran the calculator on the performance unlimited site and it seems that it may be. It is the long, thin crinkle Cobra type. You can see pictures in my gallery. Thanks again.

Joe
Reply With Quote
  #10 (permalink)  
Old 01-17-2007, 08:48 AM
RNT's Avatar
RNT RNT is offline
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2006
Location: Aiken, South Carolina, sc
Cobra Make, Engine: SPF #2457, Sunset Red/Titanium Stripes,460FR, SCJA, TKO 600
Posts: 202
Not Ranked     
Default

The Ford Racing oval filter is on my 460. Check my photos.
__________________
"The Cobra is a 40 year old design that moves people like no other".
Reply With Quote
  #11 (permalink)  
Old 01-17-2007, 08:55 AM
hkelley's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2007
Location: Greensboro NC, NC
Cobra Make, Engine: SPF #2101 Diamond Ed.; 460
Posts: 61
Not Ranked     
Default

Yep. I think that is the one I need to switch to. The one I have is longer but much thinner.

Joe
Reply With Quote
  #12 (permalink)  
Old 01-17-2007, 09:00 AM
RNT's Avatar
RNT RNT is offline
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2006
Location: Aiken, South Carolina, sc
Cobra Make, Engine: SPF #2457, Sunset Red/Titanium Stripes,460FR, SCJA, TKO 600
Posts: 202
Not Ranked     
Default

Joe, my intake is the Edelbrock RPM Performer - dual plane.
__________________
"The Cobra is a 40 year old design that moves people like no other".
Reply With Quote
  #13 (permalink)  
Old 01-20-2007, 09:06 PM
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2005
Location: Auckland, NA
Cobra Make, Engine: Superformance (SPF2265) 482cu, Tremac TKO 600R
Posts: 22
Not Ranked     
Default

Replace your factory rocker bolts with longer threads. The factory rocker bolt has about 12mm of thread and sooner or later tends to snap the rocker post clean off the SCJ Kaase heads. Also add rocker girdles to tighten everything up.
The single plane inlet manifold will fit under the hood.
Have a balance tube installed between your side pipes, this will resolve the HP drop due to the SPF factory pipes.
Nice colour car!
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 10:15 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink