 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
|
|
|
1 |
2 |
| 3 |
4 |
5 |
6 |
7 |
8 |
9 |
| 10 |
11 |
12 |
13 |
14 |
15 |
16 |
| 17 |
18 |
19 |
20 |
21 |
22 |
23 |
| 24 |
25 |
26 |
27 |
28 |
29 |
30 |
|
|
CC Advertisers
|
|
 11Likes
09-06-2013, 05:50 AM
|
|
CC Member
|
|
|
Join Date: Dec 2001
Location: Louisville,
KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,417
|
|
Not Ranked
Not doing any short blocks anymore, only completed engines. That way I can dyno them and I know they're right when they leave here.
Last edited by blykins; 09-06-2013 at 05:44 PM..
|
09-06-2013, 05:51 PM
|
|
CC Member
|
|
|
Join Date: Dec 2001
Location: Louisville,
KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,417
|
|
Not Ranked
Alright Cliff....
Got pretty far today. Had to beat the poop out of the oil pan and open up almost every single hole on the flange to get it to fit. I like Aviaid pans, but I've never had one go on without a fight.
Timing cover and balancer are on. Checked the timing marks against true TDC and found out that your adjustable pointer won't adjust to where we need it. I ordered a new one, and will throw this one in your pile.
Measured for pushrods and called Trend to get those ordered. They are a completely custom length, so it will probably be the end of next week before I get them. I wait to put the intake on until I get the pushrods installed and make sure that everything oils the way it's supposed to oil. If I have to make an adjustment on something, it's a lot easier to see what's going on with the intake off. Easier to check lifter preload that way too.
All-in-all, not much more to go. New timing pointer will go on, I'll check the balancer again, then the water pump will go on. Pushrods will come in, I'll throw the rockers on, pop the intake on, and that will pretty much be it.
 |
09-06-2013, 05:53 PM
|
|
CC Member
|
|
|
Join Date: Dec 2001
Location: Louisville,
KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,417
|
|
Not Ranked
|
09-06-2013, 06:49 PM
|
|
CC Member
|
|
|
Join Date: Oct 2003
Posts: 4,078
|
|
Not Ranked
Brent-is that a 1-piece reusable pan gasket? If so, a FelPro?
Nicely done intake ports for a 331.
__________________
Chas.
|
09-06-2013, 07:28 PM
|
|
CC Member
|
|
|
Join Date: Sep 2012
Location: Portland,
OR
Cobra Make, Engine: ERA - B2Motorsports Dart 331
Posts: 464
|
|
Not Ranked
Damn Brent - Just Awesome. I am very excited to have it. I ran my 03 at PIR this morning in the rain and was very fast compared to the others in my group.
Dancing a 3500 pound car on wet asphalt gives me some hope I can a manage this.
OTH - driving a 90 inch, 2300 lb car, with more horsepower than my 3500lb car is some cause for concern. 
Beautiful work.
 |
09-07-2013, 06:51 AM
|
|
CC Member
|
|
|
Join Date: Dec 2001
Location: Louisville,
KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,417
|
|
Not Ranked
Yes, Felpro one piece gasket.
On the head intake port, that's how it comes with a CNC cut Twisted Wedge head, made to fit a Felpro 1262 gasket.
I mocked up the Victor intake yesterday to check port alignment and it looked great. The port openings on the intake were just a little smaller than the gasket size, which is just fine as it will help with velocity on this smaller engine.
Cliff, that's why cars have gas pedals. You can control them easier that way.  |
09-07-2013, 04:38 PM
|
|
CC Member
|
|
|
Join Date: Sep 2012
Location: Portland,
OR
Cobra Make, Engine: ERA - B2Motorsports Dart 331
Posts: 464
|
|
Not Ranked
Yea - I am counting on extreme response - think we have it?
chr
|
09-07-2013, 04:44 PM
|
|
CC Member
|
|
|
Join Date: Dec 2001
Location: Louisville,
KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,417
|
|
Not Ranked
Should be pretty crisp....
|
09-08-2013, 08:10 PM
|
|
CC Member
|
|
|
Join Date: Sep 2012
Location: Portland,
OR
Cobra Make, Engine: ERA - B2Motorsports Dart 331
Posts: 464
|
|
Not Ranked
maybe we should have spun it a little faster. |
09-09-2013, 03:00 AM
|
|
CC Member
|
|
|
Join Date: Dec 2001
Location: Louisville,
KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,417
|
|
Not Ranked
It should be spinning pretty quick as it is. This is one of those engines where you're right on the fence of going to a solid cam. Always a difficult decision on one of those, "Well, I'm gonna race the car. Oh yeah, I'm going to drive it to cruises on the street too." |
09-09-2013, 10:06 AM
|
|
CC Member
|
|
|
Join Date: Aug 2012
Cobra Make, Engine:
Posts: 15
|
|
Not Ranked
Who's brite idea was that anyway?  After tracking the 03, I'm not sure I see any point in driving either of them on the street.
When will you dyno?
chr |
09-09-2013, 10:32 AM
|
|
CC Member
|
|
|
Join Date: Dec 2001
Location: Louisville,
KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,417
|
|
Not Ranked
Waiting on pushrods and then button it up. Pushrods will prob be here the end of this week. Prob end of next week or so.
Wish we would have went solid....:-(
|
09-09-2013, 12:46 PM
|
|
CC Member
|
|
|
Join Date: Aug 2012
Cobra Make, Engine:
Posts: 15
|
|
Not Ranked
Quote:
Originally Posted by blykins
Wish we would have went solid....:-(
|
Yea - I should have stuck to the original plan 
It will be good.
chr |
09-11-2013, 11:13 PM
|
|
CC Member
|
|
|
Join Date: Sep 2012
Location: Portland,
OR
Cobra Make, Engine: ERA - B2Motorsports Dart 331
Posts: 464
|
|
Not Ranked
Brent - will you post up the rockers and stuff before you button up. Also, how will you identify it as your build?
x-chr
|
09-12-2013, 03:01 AM
|
|
CC Member
|
|
|
Join Date: Dec 2001
Location: Louisville,
KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,417
|
|
Not Ranked
Pushrods came in yesterday around quitting time, along with the new distributor, etc.
Of course I'll take pictures...
Usually, they get a set of logo'd valve covers, etc. to mark it as mine, but since you're going with the Cantons, I'll probably just punch the block/heads. Is that what you're asking?
|
09-12-2013, 09:15 PM
|
|
CC Member
|
|
|
Join Date: Sep 2012
Location: Portland,
OR
Cobra Make, Engine: ERA - B2Motorsports Dart 331
Posts: 464
|
|
Not Ranked
Yea - you have to sign for it somehow. A small tag that could be stamped and attached somewhere visible would be cool.
x-chr
|
09-13-2013, 03:21 PM
|
|
CC Member
|
|
|
Join Date: Dec 2001
Location: Louisville,
KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,417
|
|
Not Ranked
|
09-13-2013, 03:44 PM
|
|
CC Member
|
|
|
Join Date: Oct 2003
Posts: 4,078
|
|
Not Ranked
Brent,
Mind posted an all-up weight when done? Carb, coil and wires-no alt. I'm guessing under 420.
Will Cliff run that System-1 or that just for dyno?
__________________
Chas.
|
09-13-2013, 04:10 PM
|
|
CC Member
|
|
|
Join Date: Dec 2001
Location: Louisville,
KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,417
|
|
Not Ranked
I don't have any scales to measure a complete engine with. It's extremely light though....I could pick the block up off the floor with one finger. The crank weighed 46 lbs.
The oil filter is mine. I use it on every engine when I dyno. |
09-13-2013, 04:21 PM
|
|
CC Member
|
|
|
Join Date: Oct 2003
Posts: 4,078
|
|
Not Ranked
That might not hurt a bathroom scale.../:<) Probably 380.
__________________
Chas.
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 04:00 PM.
Links monetized by VigLink
|
Linear Mode
