 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| 1 |
2 |
3 |
4 |
5 |
6 |
7 |
| 8 |
9 |
10 |
11 |
12 |
13 |
14 |
| 15 |
16 |
17 |
18 |
19 |
20 |
21 |
| 22 |
23 |
24 |
25 |
26 |
27 |
28 |
| 29 |
30 |
|
|
|
|
|
|
|
CC Advertisers
|
|
 6Likes
06-09-2024, 03:10 PM
|
|
CC Member
|
|
|
Join Date: May 2015
Posts: 626
|
|
Not Ranked
Weird engine trouble
So we took the wife out for a ride. Stopped for an hour, and just as we were leaving the engine started ticking/tapping. Sounded like an exhaust leak, so we drove home easy…
Background, 427 stroker, Big hydro cam, 850 dp, trickflow r manifold. Just recently discovered a bad ground at the battery, and fixed it. Car was cutting out periodically, lug was actually cracked in half…Msd 6al box. Have a spare, swapped it out and no change.
Got home and started troubleshooting, discovered that the tick/tap stopped when plug wire 7 was pulled off the distributor. Tried switching pugs and wires no change. There does seem to be a periodic arc at the plug. But insulating the heck out of it by wrapping it in a sliced hose didnt help.
Reading the internet i am worried i have a bad rod bearing? Seems strange that it would cause arcing at the plug?
I drained the oil, and see nothing in it…havent cut open the filter.
Any ideas?
Thanks
Steve H
Spf 1764
__________________
Superformance 1764
Ford Racing 427 SB
|
06-09-2024, 04:22 PM
|
 |
CC Member
|
|
|
Join Date: Feb 2006
Location: Gilroy,
CA
Cobra Make, Engine: SPF 2291, Whipple Blown & Injected 4V ModMotor
Posts: 2,700
|
|
Not Ranked
Pull the pan and stop guessing.
__________________
Help them do what they would have done if they had known what they could do.
|
06-09-2024, 05:07 PM
|
 |
CC Member
|
|
|
Join Date: Nov 2009
Location: Edmond,
Ok
Cobra Make, Engine: Classic Roadsters
Posts: 621
|
|
Not Ranked
Big hydro cam
I’d check under valve cover
Maybe lifter makes noise only when cylinder pressure is up
Do the easy stuff first
__________________
 Chaney Shores Studio
|
06-09-2024, 05:21 PM
|
|
CC Member
|
|
|
Join Date: May 2015
Posts: 626
|
|
Not Ranked
Did that
Quote:
Originally Posted by sunman
Big hydro cam
I’d check under valve cover
Maybe lifter makes noise only when cylinder pressure is up
Do the easy stuff first
|
Originally thought lifter or exh leak, pulling the plug wire and stopping the noise initially was a relief, but when i couldn’t cure it with swapping plugs/wires i started worrying. Swapped boxes, distributors, pulled the valve cover, ran it (big oily mess)…. I am seeing arcing at the plug, but even sliding a hose over the boot did nothing…
__________________
Superformance 1764
Ford Racing 427 SB
|
06-09-2024, 05:24 PM
|
|
CC Member
|
|
|
Join Date: May 2015
Posts: 626
|
|
Not Ranked
Yup
Quote:
Originally Posted by eschaider
Pull the pan and stop guessing.
|
Im on the ground no lift…did replace the pan once with help back in commiefornistan where i had help…dont have any now here in SC. That big canton pan is a bit of a ***** to get back on…
__________________
Superformance 1764
Ford Racing 427 SB
|
06-09-2024, 05:29 PM
|
|
CC Member
|
|
|
Join Date: May 2015
Posts: 626
|
|
Not Ranked
Yup
Quote:
Originally Posted by eschaider
Pull the pan and stop guessing.
|
Im on the ground no lift…did replace the pan once with help back in commiefornistan where i had help…dont have any now here in SC. That big canton pan is a bit of a ***** to get back on…
__________________
Superformance 1764
Ford Racing 427 SB
|
06-09-2024, 05:31 PM
|
 |
CC Member
|
|
|
Join Date: May 2008
Location: Brisbane,
QLD
Cobra Make, Engine:
Posts: 2,794
|
|
Not Ranked
Quote:
Originally Posted by tortuga
Originally thought lifter or exh leak, pulling the plug wire and stopping the noise initially was a relief, but when i couldn’t cure it with swapping plugs/wires i started worrying. Swapped boxes, distributors, pulled the valve cover, ran it (big oily mess)…. I am seeing arcing at the plug, but even sliding a hose over the boot did nothing…
|
Can we elaborate more on this?
You said you changed the plug AND the lead, and this still happens?
Is the sound a "sparking noise" or a "mechanical knock"?
Gary
__________________
Gary
Gold Certified Holden Technician
|
06-09-2024, 07:18 PM
|
 |
CC Member
|
|
|
Join Date: Sep 2002
Cobra Make, Engine: SPF#0760
Posts: 3,403
|
|
Not Ranked
Check your engine grounds and battery grounds.
Blas
__________________
Wiring Diagrams: SPF MKII, MKIII, GT40, CSX7000, CSX8000, Corvette Grand Sport, and Shelby Sebring, Bondurant & Cinema Tribute Cars.
Owner’s Manuals: SPF MKII, CSX7000, CSX8000, Sebring, Bondurant, Cinema Tribute Cars $ GT40’s..
Large, easy to read and trace schematics with part numbers, wire colors, wire gauge, fuses, and electrical upgrade information. Trouble-shooting and replacement part numbers for those roadside repair adventures.
SPFWiringDiagrams@Comcast.net
|
06-10-2024, 03:05 AM
|
|
CC Member
|
|
|
Join Date: May 2015
Posts: 626
|
|
Not Ranked
Grounds
Quote:
Originally Posted by Blas
Check your engine grounds and battery grounds.
Blas
|
I did just fix the battery ground. The engine ground as well.
Its just crazy how its only on one cylinder. Swapped plugs and wires?
Absolutely goes away with the #7 wire pulled at the distributor.
Oil is clean.
__________________
Superformance 1764
Ford Racing 427 SB
|
06-10-2024, 03:33 AM
|
 |
CC Member
|
|
|
Join Date: Feb 2002
Location: Dadeville,
AL
Cobra Make, Engine: Sold my EM.
Posts: 2,459
|
|
Not Ranked
I'm not big on coincidences, so when a new problem arises right after I've done work on a car, I suspect I unknowingly did something while doing the previous work. And electricity takes the path of least resistance, so the arcing tells me there is too much resistance where the electricity is supposed to be going. If it were me I'd start by adding some temporary jumper cables to know the engine and ignition are properly grounded to see if that caused the arcing to stop. If so, I'd start looking for the bad connection(s).
__________________
Tommy
Cheetah tribute completed 2021 (TommysCars.Weebly.com)
Previously owned EM Cobra
"Never attribute to malice that which is adequately explained by stupidity." - Hanlon's Razor
|
06-10-2024, 04:36 AM
|
|
CC Member
|
|
|
Join Date: May 2015
Posts: 626
|
|
Not Ranked
Agree
Quote:
Originally Posted by Tommy
I'm not big on coincidences, so when a new problem arises right after I've done work on a car, I suspect I unknowingly did something while doing the previous work. And electricity takes the path of least resistance, so the arcing tells me there is too much resistance where the electricity is supposed to be going. If it were me I'd start by adding some temporary jumper cables to know the engine and ignition are properly grounded to see if that caused the arcing to stop. If so, I'd start looking for the bad connection(s).
|
Its just too weird that after fixing the battery ground in the trunk that i now have a weird electrical issue at the engine. Find a bad bearing very hard to believe…why would that cause a plug to arc.
Why just this one plug? All one cylinder head? Was thinking maybe ill run a ground wire directly from the cylinder head? Think there are tapped 7/16-14 holes i could bolt a cable to.
For the life of me i just dont understand how the header could be more grounded than the engine. The engine ground looks and feels good, but maybe the next step is to remove it and clean it good…
__________________
Superformance 1764
Ford Racing 427 SB
|
06-10-2024, 04:51 AM
|
|
CC Member
|
|
|
Join Date: Feb 2002
Location: Dadeville,
AL
Cobra Make, Engine: Sold my EM.
Posts: 2,459
|
|
Not Ranked
You don't have to use a full size battery jumper cable to test things. A long 12 gauge wire with alligator clips will do.
__________________
Tommy
Cheetah tribute completed 2021 (TommysCars.Weebly.com)
Previously owned EM Cobra
"Never attribute to malice that which is adequately explained by stupidity." - Hanlon's Razor
|
06-10-2024, 05:50 AM
|
 |
CC Member
|
|
|
Join Date: Apr 2008
Location: Glastonbury,
Ct
Cobra Make, Engine: ERA2041 sold 2021
Posts: 241
|
|
Not Ranked
Did you check for a broken valve spring?
|
06-10-2024, 08:13 AM
|
|
CC Member
|
|
|
Join Date: Feb 2006
Location: Gilroy,
CA
Cobra Make, Engine: SPF 2291, Whipple Blown & Injected 4V ModMotor
Posts: 2,700
|
|
Not Ranked
A mechanical "ticking, tapping sound" where there was none previously does not have an electrical origin; it has a mechanical origin. You can check all the various it isn't that bad sorts of non-mechanical origins possible. When you are all done, the odds are your mechanical "ticking, tapping sound" will have a mechanical origin.
__________________
Help them do what they would have done if they had known what they could do.
|
06-10-2024, 08:32 AM
|
|
CC Member
|
|
|
Join Date: Jul 2011
Location: SEVERN,
Ont
Cobra Make, Engine:
Posts: 103
|
|
Not Ranked
I had a 65 t bird come into my shop 2 weeks ago with the same sound your describing and went away when plug wire disconnected, dropped the pan removed number 5 rod cap and bearing was gone didn't see anything bad in the oil. I hope I'm wrong but I have seen and heard this problem before.
BTW oil pressure was good.
Joey.S |
06-10-2024, 03:23 PM
|
|
CC Member
|
|
|
Join Date: Sep 2002
Location: Grand Rapids,
MI
Cobra Make, Engine: FFR Challenge Car, RDI aluminum 427w
Posts: 354
|
|
Not Ranked
My $0.02.
Joey.S brought the potential of a rod bearing. Let's follow that.
If pulling a plug wire eliminated the ignition (kaboom) in #7, perhaps that stopped the rod from pushing down on the crank journal - the tick. Now without the ignition in the #7 cylinder the crank is pulling the rod rather than the normal of having the piston push on the rod.
Hope this makes sense, sorta does to me. Otherwise just ignore my WAG.
I'd look at a lot before pulling the pan, yup a PITA with the SPF/Canton combination. Been there done that, I didn't like it either.
Jim
|
06-10-2024, 03:33 PM
|
|
CC Member
|
|
|
Join Date: Feb 2002
Location: Dadeville,
AL
Cobra Make, Engine: Sold my EM.
Posts: 2,459
|
|
Not Ranked
Perhaps one of those tiny cameras would allow you to take a peek without dropping the pan.
__________________
Tommy
Cheetah tribute completed 2021 (TommysCars.Weebly.com)
Previously owned EM Cobra
"Never attribute to malice that which is adequately explained by stupidity." - Hanlon's Razor
|
06-10-2024, 06:39 PM
|
 |
CC Member/Contributor
|
|
|
Join Date: Sep 2016
Location: (Beautiful) Sequim,
WA
Cobra Make, Engine: Pacific Roadster, 347 cu.in. 5-speed
Posts: 1,976
|
|
Not Ranked
Tommy, exc. idea, we had the same type issue, bought Steve's (Back in Black) West Coast Cobra, pulled the dip stick (Nothing but the top of it  ) Brent took his camera though the drain plug, to see if the rest of it was in the oil pan, thankfully it was not there  That camera saved us pulling the pan. Cheers Tom. |
06-10-2024, 09:09 PM
|
|
CC Member
|
|
|
Join Date: Feb 2006
Location: Gilroy,
CA
Cobra Make, Engine: SPF 2291, Whipple Blown & Injected 4V ModMotor
Posts: 2,700
|
|
Not Ranked
Unless the tiny camera has a way to remove the rod cap you will not be able to inspect the rod bearing or the crank journal.
__________________
Help them do what they would have done if they had known what they could do.
|
06-10-2024, 09:27 PM
|
|
CC Member
|
|
|
Join Date: May 2008
Location: Brisbane,
QLD
Cobra Make, Engine:
Posts: 2,794
|
|
Not Ranked
Quote:
Originally Posted by tortuga
Its just too weird that after fixing the battery ground in the trunk that i now have a weird electrical issue at the engine. Find a bad bearing very hard to believe…why would that cause a plug to arc.
Why just this one plug? All one cylinder head? Was thinking maybe ill run a ground wire directly from the cylinder head? Think there are tapped 7/16-14 holes i could bolt a cable to.
For the life of me i just dont understand how the header could be more grounded than the engine. The engine ground looks and feels good, but maybe the next step is to remove it and clean it good…
|
Do you actually SEE this spark jumping?
How about a video? That would help other eyes for diagnosis.
A suspect bad rod bearing AND a sparking issue DOES NOT HAPPEN AT THE SAME TIME.
__________________
Gary
Gold Certified Holden Technician
Last edited by Gaz64; 06-10-2024 at 09:30 PM..
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 11:11 AM.
Links monetized by VigLink
|
Linear Mode
