 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
|
|
|
1 |
2 |
| 3 |
4 |
5 |
6 |
7 |
8 |
9 |
| 10 |
11 |
12 |
13 |
14 |
15 |
16 |
| 17 |
18 |
19 |
20 |
21 |
22 |
23 |
| 24 |
25 |
26 |
27 |
28 |
29 |
30 |
|
|
CC Advertisers
|
|
09-17-2003, 01:56 PM
|
 |
CC Member
|
|
|
Join Date: Aug 2000
Location: Bakersfield,Ca USA,
ca
Cobra Make, Engine:
Posts: 871
|
|
Not Ranked
Oil Pan question
Could someone point me in a good direction for an oil pan, my car has a run of the mill chrome pan on it and when I drive it the various dips and bumps are catching the drain plug, what is the best way to go and hopefully gain a couple of inches of clearance??? Oh, it's a 351w,if I switch to a different pan say a canton is it just a straight switch,by that I mean a bolt-on,Thanks!!
__________________
Gordon Claunch
If you can't afford what you want to buy, pick up a book and learn how to make it.
|
09-17-2003, 02:24 PM
|
 |
CC Member
|
|
|
Join Date: Mar 2002
Location: so cal,
Cal
Cobra Make, Engine: I used to fix them for a living
Posts: 2,563
|
|
Not Ranked
New pan usually means new oil pump pickup, unless the two pans are the exact same depth. Chrome pans are often leakers, and they keep your oil hot due to their low IR emmissivity. I like milodon pans, they are affordable, robust, and have relatively straight and flat gasket rails.
__________________
In a fit of 16 year old genius, I looked down through the carb while cranking it to see if fuel was flowing, and it was. Flowing straight up in a vapor cloud, around my head, on fire.
|
09-17-2003, 05:15 PM
|
 |
CC Member
|
|
|
Join Date: Jul 2001
Location: Senoia,
Ga.
Cobra Make, Engine: 427SO with big twin autolite inlines on custom intake, jag rear, top loader, wembeldon white, guardsmen blue stripes
Posts: 3,155
|
|
Not Ranked
Gordon, check my pics.........
__________________
Perry
Remember!, there's a huge difference between a 'parts' changer, and a mechanic.
|
09-17-2003, 05:56 PM
|
|
CC Member
|
|
|
Join Date: Aug 2000
Location: Bakersfield,Ca USA,
ca
Cobra Make, Engine:
Posts: 871
|
|
Not Ranked
That's what I'm talkin about Perry!!Looks like you shaved some off the Bell housing also.
__________________
Gordon Claunch
If you can't afford what you want to buy, pick up a book and learn how to make it.
|
09-18-2003, 08:23 AM
|
 |
CC Member
|
|
|
Join Date: Mar 2000
Location: Fairfield, NJ, USA,
NJ
Cobra Make, Engine: A & C, 351W, Tremec 3550. Exiled Member: Club Cranky
Posts: 5,897
|
|
Not Ranked
I have the Milodon Cobra Road Race pan. I've had it in over three years and it has always been leak free. It has an threaded port for the temp sender too. Got the best price from PAW out in CA.
Roscoe
__________________
Roscoe
"Crisis occurs when women and cattle get excited!"....James Thurber
|
09-18-2003, 08:30 AM
|
 |
CC Member
|
|
|
Join Date: Dec 2000
Location: Broken Arrow. OK ( South Tulsa), USA,
OK
Cobra Make, Engine: 66 COBRA FE 427 /4SP. (HCS Coupe w/ 408 Stroker and TKO 600 -sold)
Posts: 5,595
|
|
Not Ranked
Gordon,
On our cars as low as they are designed I highly recommend cutting a good inch off your Lakewood or McCloud bell housing. It doesn't hurt a thing and allows you to get your car out of most trailers without getting hung up on the bell housing.
I havent cut mine yet but I will when I install a new clutch.
Clois
__________________
Sunshine, Asphalt and no stop signs...Perfect
"Let's roll"
"Be part of Something Good
......Leave Something Good Behind!"
from CD "Long Road Out of Eden"
|
09-18-2003, 08:38 AM
|
 |
CC Member
|
|
|
Join Date: Sep 2002
Location: Hickory,
NC
Cobra Make, Engine: ERA 427SC w/427so, ERA GT #2002
Posts: 1,106
|
|
Not Ranked
Always avoid chrome anything that seals oil with a gasket unless you bead blast the surface that the gasket seals against. This will give the pan, valve cover or whatever something to "bite" into the gasket.
As for the bottom of the bellhousing, scribe a line tangent with the very bottom of the horizontal section of the bellhousing and saw off--not flame cut--the flange. Don't forget the engine plate.
__________________
Tom
"If you can make black marks on a straight from the time you turn out of a corner until the braking point of the next turn, then you have enough HORSEPOWER." Mark Donohue
|
09-18-2003, 05:39 PM
|
|
CC Member
|
|
|
Join Date: Jul 2001
Location: Senoia,
Ga.
Cobra Make, Engine: 427SO with big twin autolite inlines on custom intake, jag rear, top loader, wembeldon white, guardsmen blue stripes
Posts: 3,155
|
|
Not Ranked
The teflon skids are about an inch below the pan and, they saved me more than once, I used the old reliable porta band saw on the scatter shield. I like the way a cobra looks when it's low.
__________________
Perry
Remember!, there's a huge difference between a 'parts' changer, and a mechanic.
|
09-19-2003, 11:07 AM
|
 |
Renegade Nuns on Wheels
|
|
|
Join Date: Aug 2001
Location: columbus,
Oh
Cobra Make, Engine: Unique 427 roadster with 351C-4B
Posts: 5,129
|
|
Not Ranked
Armondo
I bought my pan from Armondo out n cali (do a search for contact info), he makes a very nice pan. Fully baffled and trap door, windage, 'scraper', new pick up, rail type pan. 8+ quart capacity and I picked up a couple of inches of ground clearence. Aviad style and quality for about a C note less. My install I just unbolted the pan, installed the pick-up and that was it. Didn't need to pull the starter or any thing.
Rick
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 04:38 AM.
Links monetized by VigLink
|
Linear Mode
