 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
|
|
|
1 |
2 |
| 3 |
4 |
5 |
6 |
7 |
8 |
9 |
| 10 |
11 |
12 |
13 |
14 |
15 |
16 |
| 17 |
18 |
19 |
20 |
21 |
22 |
23 |
| 24 |
25 |
26 |
27 |
28 |
29 |
30 |
|
|
CC Advertisers
|
|
 1Likes
04-11-2012, 06:23 AM
|
|
CC Member
|
|
|
Join Date: Mar 2006
Cobra Make, Engine:
Posts: 231
|
|
Not Ranked
So what are the dimensions for the first emblem? Was it big or small, any sizes?
Emblem S1CS-A or the first (54?) cars.
Cheers
Migge
|
04-11-2012, 06:43 AM
|
|
CC Member
|
|
|
Join Date: Dec 2011
Location: York Co. Maine USA,
ME
Cobra Make, Engine: ERA 427 S/C W/Holmon Moody Original Nascar build #508 Iron Block/heads (C5AE-H) Bal/Blu 427 Sideoiler; 780 Holley Dbl. Pump; 4 Speed Top Loader; AP Racing Bks; IRS; 15" Trigo pins
Posts: 391
|
|
Not Ranked
Hmm, If I remember my friends 260 (#53) AC had no badges. Except the side badges "powered by ford". I'm not suprised, that there were serval different adaptations in the beginning.  |
04-11-2012, 07:39 AM
|
|
CC Member
|
|
|
Join Date: Mar 2006
Cobra Make, Engine:
Posts: 231
|
|
Not Ranked
Not really my answers :-(
|
04-12-2012, 06:56 AM
|
 |
CC Member
|
|
|
Join Date: Nov 2001
Location: Windham,,
Me
Cobra Make, Engine:
Posts: 1,590
|
|
Not Ranked
My choice was made after looking at as many pictures of orginal AC Cobras as needed to get that look.Only ones I compromised on were front fender badges instead of 427 mine have 460.
|
04-12-2012, 09:56 AM
|
|
CC Member
|
|
|
Join Date: Mar 2006
Cobra Make, Engine:
Posts: 231
|
|
Not Ranked
Dimensions PLEASE!!!!
|
04-12-2012, 10:36 AM
|
 |
CC Member
|
|
|
Join Date: Jun 2008
Location: Chester Springs,
PA
Cobra Make, Engine: Kirkham 289 FIA #690, FRPP 427 Boss engine
Posts: 764
|
|
Not Ranked
Man, you are so demanding of an old thread!
These are reproductions, but:
1 15/16"
2 5/16"
__________________
RCR GT40 SOLD to Fast 5
Kirkham #690 289 FIA
|
04-12-2012, 11:00 AM
|
|
CC Member
|
|
|
Join Date: Mar 2006
Cobra Make, Engine:
Posts: 231
|
|
Not Ranked
Thanks a lot, but I mean the OLD FIRST logo "SHELBY AC COBRA" or known as S1CS-4, page 3 in the thread.
|
04-18-2012, 05:24 AM
|
 |
CC Member
|
|
|
Join Date: May 2010
Location: Indy,
IN
Cobra Make, Engine: Shelby American CSX6046 S/C 427 (482) Shelby CSX1006
Posts: 59
|
|
Not Ranked
Quote:
Originally Posted by HIQ
It is appropriate to put AC badges on the car IF it is an AC. It is appropriate to put Shelby Cobra badges on a car IF it is a Shelby Cobra.
Why mark the car as something it is not?
|
This makes sense to me, good answer. |
05-14-2012, 12:48 PM
|
 |
CC Member
|
|
|
Join Date: May 2006
Location: Denia / SPAIN,
ESP
Cobra Make, Engine: NAF 289 Blue/White strips
Posts: 188
|
|
Not Ranked
No dimensions of the "Old Shelby AC Cobra" , emblem nr. S1CS-A availabel?
Rico
__________________
Rico, NAF 289
Last edited by cobra 53; 05-14-2012 at 12:53 PM..
|
05-15-2012, 01:31 AM
|
|
CC Member
|
|
|
Join Date: Mar 2006
Cobra Make, Engine:
Posts: 231
|
|
Not Ranked
From calculations and relations boot handle, number plate lamp etc. it must be 78 mm, a little over 3", so I guess 3" is correct. I have an answer from Dave and he said 74 mm wide, so just under 3". I 'll find out end of this month in SPA, where I can take some mesurements. Hope to see CSX 2049 or 2051 again.
|
05-29-2012, 06:04 AM
|
|
CC Member
|
|
|
Join Date: Mar 2006
Cobra Make, Engine:
Posts: 231
|
|
Not Ranked
It is exac. 74 mm wide, pic is not very correct because of the angle.
|
05-29-2012, 08:40 AM
|
|
CC Member
|
|
|
Join Date: Aug 2001
Cobra Make, Engine: CSX Cars
Posts: 754
|
|
Not Ranked
If anyone wants the AC badges I had them made a few years ago, I have four left and I would sell them for $60 each unfinished. In order to finish you need to use touch up paint and the clear coat. Some sanding will also be required. I have showed what they looked like once done. The ones I have are rough aluminum.
csx7034 at g mail dot com
Thanks,
Allan
I have the units on CNC with the supplier so if there was a number of guys who wanted them they still could be made.
__________________
A happy SAI customer
Cobra Make & Engine: Continuation Series Shelby Cobra, CSX 7034 the most accurately detailed Continuation Cobra to original specification since the demise of CSX 4027.
|
05-29-2012, 10:31 AM
|
|
CC Member
|
|
|
Join Date: Mar 2006
Cobra Make, Engine:
Posts: 231
|
|
Not Ranked
Not bad but also not very original made, sorry.
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 07:24 PM.
Links monetized by VigLink
|
Linear Mode
