|
Ramps
I used 2 X 4 blocks on both ends. I drilled into the concrete floor and installed anchors. To place or remove the blocks I just use my cordless drill. Set up time for the whole ramp system is about 2 minutes. Just be sure where you want the ramp located before you drill. This location is where the ramps will be each time you set up.
John |
RedBarchetta,
You have an email your way on more information on the design of your poor man's qwik lift. RedSabre Oops, did not see the other pages on this thread as I went from top to bottome and missed the middle that outline the design. Please ignore my email as I think I have what I needed. Thanks. |
Very poor man's lift
I used Dean's idea and build mine out of old shipping crate material from Italy.The wood stands I painted black and the metal ( 3" x 10", really some metric size ) I painted Ford Blue. I cut two 3" x 7" tube steel in half and welded them to a 7" piece to get the 10" + - width. I pinned the bridge and ramps to the wood stands. The height is 13 1/4", just right for working under the car. One person can easily put it up or take it down. Stores in a 10' x 14" space.
Cost about 10 lbs of flux core and a gal of paint and primer, about $75. And some screws and 1/4 x 20 bolts and fender washers. Oh yes, a lot of hours. Dwight http://www.clubcobra.com/photopost/d...m/DSCN2110.JPG http://www.clubcobra.com/photopost/d...m/DSCN2271.JPG http://www.clubcobra.com/photopost/d...m/DSCN2270.JPG I can remove the bridge to work under the car, but most of the time I leave them in place http://www.clubcobra.com/photopost/d...m/DSCN3644.JPG long but fun story behind this picture http://www.clubcobra.com/photopost/d...m/DSCN2046.JPG |
Another option to keep the ramps from walking is to drill a hole in the floor big enough to put in a small dia pc. of water pipe. buy a long grade 8 bolt that will fit comfortably in the pipe, drill a hole in a 12" pc of 2" x 4" that the bolt can slip through.
Slip the bolt through the 2 x 4, then into the pipe. Needs a couple of inches into the floor. Now snug your ramp end up against the 2 x 4 and drive up. When you want to pull it all apart, just slip up the bolt and 2 x 4 and find a pc. of plastic rod that will fill your pipe. You can drill a hole in the plastic, stick in a big nail and use a magnet to pull it up out of the hole. Or leave the block and bolt in place to use as wheel chocks when you drive in rampless. My ramp is similar in theory but 18" high. I have long ramps into the garage and they get removed once the car is up. I have similar spans at the middle that can be removed. I'm not into the form as much so it looks pretty crude but it's been used constantly for the past 2.5 years. I used a local hardwood to ensure strength. We have had our SUV up on it several times too. Dean's and Dwight's are pcs. of art. Very impressive and glad you guys shared. Ken |
RedBarchetta...Patent your design and sell it.. Great product!
|
Hey, I set a fire while grinding away, once, only once! :LOL:
|
AWESOME!!!!! My hats off to you! Great idea & great looking finished product!
Sure is one nice looking Cobra too! What size are the front & rear wheels? I like the combination. Randy |
Quote:
Regards, -Dean P.S. I have received numerous private e-mails on the subject of these ramps. I'm encouraged that others have built their own version of the "Poor Man's Qwik Lift." These ramps have held up quite well so far (nearly two years...seems longer). While I'd still like to have a real Qwik Lift or a four-post, this has proved to be an economical alternative for those of us on a budget. The toughest hurdle is just gathering the courage to drive up/down them. Not sure if I wrote this previously, but I now have hung a couple ping pong balls from the ceiling in a row...like a gun sight. I have them lined-up with the hood hinge on the driver's side. I just line myself up, hinge to ping pong balls, and drive up and I'm usually within 1" of center every time. What do they say...necessity is the mother of invention? :) |
Thanks for the tire/wheel info. I really like the set-up. I'll be getting the tires/wheels for my Cobra in a few months, now I know what sizes to look for.
Once again, that is one clean looking Cobra you have! Randy |
Mirror, mirror on the wall...
Quote:
Ralph |
Ralph, I thought about that while I was sawing the thing together. I was originally thinking of installing one of those round "fish-eye" mirrors that you install at a corner walkway. Then perhaps putting a large mirror on the back wall of the garage, set at a 45 degree angle so that I could see my "trajectory" from the garage opening. The ping pong balls hanging from the ceiling ended up being the easiest and cheapest solution....and arguably the best! :LOL:
Even with the visual aids, I recommend anyone driving up ANY ramp for the first time to have someone spot you until you get comfortable with it. -Dean |
I'm bumping this back to the top because there are a lot of new guys that might be interested in Dean's Poor man ramp's.
Dwight |
I left mine natural wood.
They lift about 12 to 13 inches in the air ( I think ) But, since I got my Rotary, I haven't used then. :D |
Thanks, Dean!
For some reason, I had never seen this before. What a great idea! If I don't get some stuff cleared out to make room for a lift for next winter, I'll build one. Lowell |
Poor man lift
I watch the front tire and the edge of the ramp as I drive up. After a few times it's easy. The first time you need someone to watch to make sure you have the ramp in the correct place and your not driving off of it. Go very slow the first time. I installed pins into the bridge and ramp to keep them from moving. I spun one of the rear ramps to the floor one time. Installed the pins (1/4 rod with fender washer welded to the rod) the next day. I have marked the floor where the stands go to make it easier to set up. I do not have mine anchored to the floor and have not had a problem. I have 10' ramps and I think they makes it easier to drive onto with out walking the whole thing. My Cobra buddies come over and use the ramp all the time. I like the lift and want to thank Dean for the idea. It's a great tool in mine garage.
Thanks Dean Dwight |
mirrow
Doc borrowed my fish eye mirrow and installed it in Coach Mike's new Cobra. :LOL: Coach didn't like it, so he removed it. Maybe I can hang it in front of the ramp?
Dwight http://www.clubcobra.com/photopost/d...m/DSCN3334.JPG |
Wow, this is awesome!!! I had factored a 2 post into my cobra budget but this could work great!!!! I keep a portfolio of great ideas for the garage, cars, etc. I printed this and it's going in there!
What do you think the max wieght is that this can handle? If SHOULD be pretty darn sturdy! Josh |
Does anyone know how high the car will sit from the ground to the chassis clearance with this setup?
Very Very Nice!!! |
Dwight and others,
Thanks for the accolades, but I honestly have to give credit to a guy on corvetteforum.com that I 'lifted' the idea from about 5 years ago. He was a carpenter by trade and had a C4 that he used it on. I just had to make a few minor adjustments to fit the Cobra chassis and accommodate the wider rear track. Yeah, the first couple drives up and down can have a little pucker factor :LOL: , but once you get the hang of it they really work well. So far I have had only one end support (6" 2x4) on one of the bridges actually split a little. Even with that ding, it's still very stable and it's great to keep the undercarriage clean and to perform general R&R without using a floorjack. I'm also tall (6'3"), so reaching into the engine bay doesn't require a lot of stooping and that saves the back. I built the ramps with the intentions of eventually getting a true Qwik Lift. But they have worked so well that I've used that money for mods on the car. :) Have a great week, everyone! -Dean |
Quote:
-Dean |
| All times are GMT -7. The time now is 04:49 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: