 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
|
|
|
1 |
2 |
| 3 |
4 |
5 |
6 |
7 |
8 |
9 |
| 10 |
11 |
12 |
13 |
14 |
15 |
16 |
| 17 |
18 |
19 |
20 |
21 |
22 |
23 |
| 24 |
25 |
26 |
27 |
28 |
29 |
30 |
|
|
CC Advertisers
|
|
 2Likes
02-23-2009, 07:37 PM
|
 |
CC Member
|
|
|
Join Date: Feb 2009
Location: Duluth,
GA
Cobra Make, Engine: 65 Factory Five MKIII Cobra
Posts: 110
|
|
Not Ranked
Quote:
Originally Posted by Bryan Wilson
|
Oh man, I really like the look of those. I went to the website but couldn't find at first glance. I'll go back and look again when I have some time. Do you remember the cost - in U.S. Dollars? |
12-10-2015, 01:26 PM
|
|
Registered User
|
|
|
Join Date: Dec 2015
Cobra Make, Engine: Factory Five, 347 Stroker
Posts: 2
|
|
Not Ranked
Hi,
I know these threads are old. I haven't had much like in finding these anywhere. Anyone know the best place to locate these fender SPATS?
|
12-10-2015, 03:19 PM
|
 |
CC Member
|
|
|
Join Date: Oct 2002
Location: Eagle,
Ne.
Cobra Make, Engine: 1966 Lone Star 427SC.
Posts: 4,307
|
|
Not Ranked
I was not happy with the ones you can buy, so I just made them out of leather and my wife sewed the edges. I lightly glued them on so I can replace them someday. Low cost and easy. 
__________________
Regards,
Kevin
|
12-20-2015, 02:08 PM
|
 |
CC Member
|
|
|
Join Date: Oct 2011
Location: Sour Lake,
Tx
Cobra Make, Engine: CMC #437, 408ci
Posts: 110
|
|
Not Ranked
I ordered a 2'x5' sheet of carbon fiber look sheeting off of ebay for $17. Measured it out and put them on with the help of a heat gun. Fairly easy and look good. Had to trim a bit due to stretch using the heat gun.
__________________
Scott
|
12-20-2015, 02:22 PM
|
|
CC Member
|
|
|
Join Date: Oct 2011
Location: Sour Lake,
Tx
Cobra Make, Engine: CMC #437, 408ci
Posts: 110
|
|
Not Ranked
Kinda hard to see. Put it on top of the doors, also.
__________________
Scott
|
06-22-2016, 03:23 PM
|
 |
CC Member
|
|
|
Join Date: Feb 2014
Location: White City,
SK
Cobra Make, Engine: West Coast, 460 CID
Posts: 2,908
|
|
Not Ranked
I know some folks have used Plasti Dip, but my fenders have a few chips that I think will show through Plasti Dip, so I'm looking for something that's perhaps a bit thicker, with a bit more hiding power. Anybody use undercoating spray or liquid? Something like this: Kleen-Flo | Products - Tumbler Paintable Rubberized Undercoating
__________________
Brian
|
06-22-2016, 04:12 PM
|
|
CC Member
|
|
|
Join Date: Oct 2002
Location: Eagle,
Ne.
Cobra Make, Engine: 1966 Lone Star 427SC.
Posts: 4,307
|
|
Not Ranked
You can always use body filler in the small holes, sand and apply what you want.
__________________
Regards,
Kevin
|
06-22-2016, 07:20 PM
|
 |
CC Member
|
|
|
Join Date: Dec 2010
Location: Tempe,AZ-High Point,NC,
AZ
Cobra Make, Engine: Kirkham #684, 482FE, Mike Mccluskey build
Posts: 2,520
|
|
Not Ranked
Quote:
Originally Posted by wtm442
Do a search within CC for 3M.
My car had the 3M Invicta Shield applied when it was brand new by a company near the SPF dealer. It cost $450 and was/is warrantied for 5 years.
Very hard to see the shield, even on my titanium Cobra.
Can you see the shield on the front end or the leading edges of the rear flare?
I would recommend it to anyone. |
They will do clear bra here for $50 bucks a side.
__________________
PRIDEnJOY
|
06-22-2016, 08:00 PM
|
 |
CC Member
|
|
|
Join Date: Feb 2000
Location: St. Lucia, West Indies,
WI
Cobra Make, Engine: Unique 427SC 383 stroker
Posts: 3,765
|
|
Not Ranked
I'm in the process of another rebuild on my Unique. It's an older body style so it has the street roadster style rear flares and once again I'm contemplating ditching the roll bar and sidepipes. This thread rekindled my interest in sourcing the polished aluminum spats and it seems the only place they are available is at Europa Spares in jolly olde Blighty. A search of their site revealed these:
http://www.europaspares.com/wheel-ar...rch-spats.html
__________________
Tropical Buzz
Grant me the serenity to accept the things I cannot change, the strength to change the things I can, and the wisdom to know the difference. -(wasn't me)
BEWARE OF THE DOGma!! Dogmatism bites...
|
06-23-2016, 07:15 AM
|
|
CC Member
|
|
|
Join Date: Feb 2003
Location: Jonesboro GA,
Posts: 382
|
|
Not Ranked
I've posted this before.
I used to manufacture clear bras and have plenty of old stock. I'm not interested in doing a 3M front bra, but anyone in the Atlanta area can get spats or other small areas done here for the price of gas and some beer to drink while WE do it. What I won't do is let you drop off the car for me to work on, that costs $$. This is for clear only. I don't do the CF. You can use my wheel if you want to give aluminum ones a try.
Last edited by mikeinatlanta; 06-23-2016 at 07:17 AM..
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 12:22 PM.
Links monetized by VigLink
|
Linear Mode
