Club Cobra Gas - N Exhaust  

Go Back   Club Cobra > Manufacturers, Engine Builders, tools, and parts. > BackDraft Racing ---

Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
Keith Craft Racing
MMG Superformance
Advertise at CC
Banner Ad Rates
MMG Superformance
Keith Craft Racing
MMG Superformance
December 2024
S M T W T F S
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31        

Kirkham Motorsports

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #1 (permalink)  
Old 03-12-2014, 05:39 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2013
Location: Sparta, nj
Cobra Make, Engine: Backdraft 1048
Posts: 270
Not Ranked     
Default Rear suspension adjustments

I noticed today the driver rear is sitting about an inch an half lower than the passenger side and was wondering how do you adjust the rear suspension to compensate for this.
__________________
Gary
Backdraft 1048
Reply With Quote
  #2 (permalink)  
Old 03-12-2014, 06:40 AM
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2010
Location: Lewisville, TX
Cobra Make, Engine: BDR, 302
Posts: 273
Not Ranked     
Default

Pretty simple adjustment after Jay and others explained how to do it. Jack it up, remove the wheel, and locate a spanner nut inside the spring. Turn it to adjust the pad that adjusts the height. You should be able to do it with channel lock pliers or even with a long screw driver.
Reply With Quote
  #3 (permalink)  
Old 03-12-2014, 11:32 AM
Kobura's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2012
Location: Saratoga, CA
Cobra Make, Engine: Backdraft RT3 #1133, Ford Racing 306
Posts: 222
Not Ranked     
Default

Here is the setup on my car #1133. The adjusting nut is on the upper support post.
Attached Images
 
Reply With Quote
  #4 (permalink)  
Old 03-12-2014, 11:37 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2013
Location: Sparta, nj
Cobra Make, Engine: Backdraft 1048
Posts: 270
Not Ranked     
Default

Thanks, A picture really clears it up. So to raise or lower the rear you just turn the top bolt. Is there a set screw or something to stop it from moving.
__________________
Gary
Backdraft 1048
Reply With Quote
  #5 (permalink)  
Old 03-12-2014, 01:25 PM
Kobura's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2012
Location: Saratoga, CA
Cobra Make, Engine: Backdraft RT3 #1133, Ford Racing 306
Posts: 222
Not Ranked     
Default

There is no provision for keeping the nut from turning except for friction. If you believe that the car has lowered about an inch and a half, you definitely need to take a look at the spring and suspension assembly. There are rubber pads and metal washers that sandwich the spring which, in addition to the spring, may not be in the condition that they should be. The most difficult part of adjusting the ride height should be removing the wheel.
Reply With Quote
  #6 (permalink)  
Old 03-12-2014, 04:20 PM
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2010
Location: Lewisville, TX
Cobra Make, Engine: BDR, 302
Posts: 273
Not Ranked     
Default

My BDR is an older build and the suspension looks different. I have the car in storage right now so I can't take a pic right now. But I'm sure that the spanner nut is on the inside of the spring. Unless my memory ain't so good.
Reply With Quote
  #7 (permalink)  
Old 03-13-2014, 03:43 PM
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2009
Location: Mooresville, NC
Cobra Make, Engine: BDR, Stroked small block
Posts: 117
Not Ranked     
Default

If the nut is hard to turn, you may need to lesson the pressure on the spring/nut. I unbolted the Shock and it made it much easier.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 06:10 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink