Club Cobra GasN Exhaust  

Go Back   Club Cobra > Manufacturers, Engine Builders, tools, and parts. > BackDraft Racing ---

Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
Keith Craft Racing
Advertise at CC
Banner Ad Rates
MMG Superformance
December 2024
S M T W T F S
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31        

Kirkham Motorsports

Like Tree4Likes

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #1 (permalink)  
Old 05-25-2018, 01:58 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Location: Mokena, IL
Cobra Make, Engine: Backdraft SBF-302
Posts: 325
Not Ranked     
Default #6 plug boot shorts to header

I'll look to attach an image later.

I noticed that my #6 plug wire boot had a hole at the bend, and was shorting to the header.

Replaced all the plug wires.

First drive #6 burned through the boot and was again arcing to the exhaust header.

The only remedy I can think of is to remove the header and dimple that tube.

OEM BDR headers attached to crate 302.

Any assistance would be sincerely appreciated.

Roy
Reply With Quote
  #2 (permalink)  
Old 05-25-2018, 02:09 PM
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2011
Location: Santa Clarita, CA
Cobra Make, Engine: Factory Five Mk4, Ford Racing Z427
Posts: 32
Not Ranked     
Default

Do you have room to install some heat insulating sleeves?

https://www.jegs.com/c/Spark-Plug-Wi...10401/10002/-1
Reply With Quote
  #3 (permalink)  
Old 05-25-2018, 03:01 PM
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2007
Cobra Make, Engine: SPF GT40
Posts: 237
Not Ranked     
Default

Like previous poster said- use boot insulators. I had your problem on my GT40. Even if insulator touches the header they still work.
Reply With Quote
  #4 (permalink)  
Old 05-25-2018, 03:16 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Location: Mokena, IL
Cobra Make, Engine: Backdraft SBF-302
Posts: 325
Not Ranked     
Default

^^^^
ohhh, I have the insulator and didn't install.
I figured if it touched the header it just wouldn't work.

Thanks fellas, I'll source a new wire without a gaping arc hole and start again.
Reply With Quote
  #5 (permalink)  
Old 05-25-2018, 04:00 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Location: Mokena, IL
Cobra Make, Engine: Backdraft SBF-302
Posts: 325
Not Ranked     
Default

but it won't stop the arc, right ?

nobody seems to sell single wires
Reply With Quote
  #6 (permalink)  
Old 05-25-2018, 04:07 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2015
Posts: 1,442
Not Ranked     
Default

If you don't have the plug wire actually on the plug or if the plug is bad it will Arc at the Sh!t connection and burn a hole in the boot.

I'd pull the spark plug. If it can't fire the electricity is trying to find a path.

Since you installed a new set of wires and have the same exact results (burned #6 boot) your most likely running on 7 cylinders.

Autolite is running a rebate on several plug lines right now.
http://www.autolite.com/media/18879/...s-2018-web.pdf

AR3924 would be the race application for your engine (cutback ground strap)

Last edited by spdbrake; 05-25-2018 at 04:14 PM.. Reason: adding info
Reply With Quote
  #7 (permalink)  
Old 05-25-2018, 04:43 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Location: Mokena, IL
Cobra Make, Engine: Backdraft SBF-302
Posts: 325
Not Ranked     
Default

I do think she's running on seven.
The unburnt fuel pops on decel.

Didn't know a lazy plug could do that.

Thanks for letting me know where to look.
I had that plug out and thought it looked normal.

edit: it's running NGK-UR45GP (G-Power) gapped .052

Last edited by Ozzie Goat; 05-25-2018 at 06:46 PM..
Reply With Quote
  #8 (permalink)  
Old 05-25-2018, 04:55 PM
Gaz64's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2008
Location: Brisbane, QLD
Cobra Make, Engine:
Posts: 2,797
Not Ranked     
Default

Electricity follows the path of least resistance.

A plug boot heated enough to insulation failure will allow the spark to short to ground especially with large spark plug gaps.

I had plug boots short to ground with 10mm gaps around the boots.

Gary

Last edited by Gaz64; 06-11-2018 at 05:18 PM..
Reply With Quote
  #9 (permalink)  
Old 06-07-2018, 01:53 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Location: Mokena, IL
Cobra Make, Engine: Backdraft SBF-302
Posts: 325
Not Ranked     
Default

I'm running out of options, and this is dumb.

I'm going to get the Taylor wires and see if they defy physics.

I have replaced all the plugs.
I verified the connection as I installed the new wires.
I used a heat sleeve over the plug wire boot etc

Didn't last ten miles. Arc to the header through the lot.

Only other idea is the dimple the header tube.

Last edited by Ozzie Goat; 06-07-2018 at 01:55 PM..
Reply With Quote
  #10 (permalink)  
Old 06-07-2018, 02:21 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2015
Posts: 1,442
Not Ranked     
Default

The .052" gap your running (most common is 035-040") could be pushing it to find a better path. I'm guessing you dont have the spark plug holes slathered in anti-seize? It can act as an insulator.

Being in proximity to the header pipe 1/2-1" is not an issue. Laying against it is, as it will melt the wire casing.

The last item still on that plug run is the dist cap. Its a stretch though. Although I have seen MSD caps with 1 spark target installed backwards but that just causes random misfires.
Reply With Quote
  #11 (permalink)  
Old 06-07-2018, 02:38 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Location: Mokena, IL
Cobra Make, Engine: Backdraft SBF-302
Posts: 325
Not Ranked     
Default

Thanks Spd. Tips help me not lose it.

I don't know whether to park it. You are correct my assembly has been dry, will seek the grease, and sacrifice another wire !
Reply With Quote
  #12 (permalink)  
Old 06-07-2018, 02:47 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Location: Mokena, IL
Cobra Make, Engine: Backdraft SBF-302
Posts: 325
Not Ranked     
Default

add to the list of things I don't understand:
can I simply gap to .040 and go on ... ?
Reply With Quote
  #13 (permalink)  
Old 06-07-2018, 02:59 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2015
Posts: 1,442
Not Ranked     
Default

Yup you can re-gap to .040. I'd spin the dizzy cap 180 and reinstall it. If the issue is the cap it will rear its head on the other bank.

Just a light coat of anti-seize on the plug threads is what I meant. Too much is not gonna help.
Reply With Quote
  #14 (permalink)  
Old 06-07-2018, 04:53 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Location: Mokena, IL
Cobra Make, Engine: Backdraft SBF-302
Posts: 325
Not Ranked     
Default

well, that worked - sort of

made it 40min/20miles before blowing out the wire (double earlier results). .040 gap with dielectric grease with a new wire

next up, Accel shorty plugs for headers. need some space between that boot and a ground.
Path of least resistance now appears to be away from the plug.

Last edited by Ozzie Goat; 06-11-2018 at 04:17 PM..
Reply With Quote
  #15 (permalink)  
Old 06-11-2018, 04:18 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Location: Mokena, IL
Cobra Make, Engine: Backdraft SBF-302
Posts: 325
Not Ranked     
Default

after that, I'm out of moves
Reply With Quote
  #16 (permalink)  
Old 06-11-2018, 04:46 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2015
Posts: 1,442
Not Ranked     
Default

That's somewhat heartening to hear. Have you flipped the dizzy cap yet?

Can you post a pic of the cable run and plug as installed?
Reply With Quote
  #17 (permalink)  
Old 06-11-2018, 04:56 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Location: Mokena, IL
Cobra Make, Engine: Backdraft SBF-302
Posts: 325
Not Ranked     
Default

Since this is the only cylinder clearance challenged and misbehaving I have not flipped the dizzy cap.

A picture would help. (edit, oh lord I'm sorry; I meant it would help if I provided an image)
Agreed that at some point I should reverse the cap installation.

Last edited by Ozzie Goat; 06-11-2018 at 06:15 PM..
Reply With Quote
  #18 (permalink)  
Old 06-11-2018, 05:07 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2015
Posts: 1,442
Not Ranked     
Default

Sorry, I meant to take the plug wire s off the cap, spin the cap 180 degrees and reinstall it. Then reattached the plug wires again.

Another question. What type of header bolts are you running and have you check them for tightness? I'm suspecting you may have a blown header gasket. Easy to check at idle with a BBQ gas lighter.
When I bought my BDR, I found 3 header bolts missing on the right bank and 2 missing on the left @ 785 miles on the odometer. I installed ARP Drilled head header bolts and Inconel safety wire.

Last edited by spdbrake; 06-11-2018 at 05:19 PM.. Reason: more info
Reply With Quote
  #19 (permalink)  
Old 06-11-2018, 05:33 PM
Gaz64's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2008
Location: Brisbane, QLD
Cobra Make, Engine:
Posts: 2,797
Not Ranked     
Default

I've never heard of a plug lead having such a short life.

Could be a combination of the gap to the header, and a possibly cylinder head grounds. If in doubt, add some ground straps directly to the heads.

Gary
__________________
Gary

Gold Certified Holden Technician
Reply With Quote
  #20 (permalink)  
Old 06-11-2018, 06:18 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Location: Mokena, IL
Cobra Make, Engine: Backdraft SBF-302
Posts: 325
Not Ranked     
Default

Thanks Gents.

I like the idea of grounding straps for the heads.
I will check the TQ of the header bolts, since they are a star pattern a tool purchase is required.

I assume if the gasket is blowing hot air at that plug, then it blows out the BBQ lighter ??
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 10:06 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink