 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| 1 |
2 |
3 |
4 |
5 |
6 |
7 |
| 8 |
9 |
10 |
11 |
12 |
13 |
14 |
| 15 |
16 |
17 |
18 |
19 |
20 |
21 |
| 22 |
23 |
24 |
25 |
26 |
27 |
28 |
| 29 |
30 |
31 |
|
|
|
|
|
|
CC Advertisers
|
|
 33Likes
09-01-2022, 09:43 AM
|
 |
CC Member
|
|
|
Join Date: Nov 2009
Location: Edmond,
Ok
Cobra Make, Engine: Classic Roadsters
Posts: 628
|
|
Not Ranked
Kevin the complete small block RCC suspension I bought in 1999 have aluminum tags on the springs. I thought they had an “AVO” stamped on them.
Pulled them off and it turns out that flipped over they say “170” on rears and “350” on the front springs.
Hey, when installing airbags ya ditch the springs anyway.
Party On
__________________
 Chaney Shores Studio
|
09-01-2022, 11:09 AM
|
|
CC Member
|
|
|
Join Date: Aug 2021
Location: Beaumont,
TX
Cobra Make, Engine: Classic Roadsters, Ford coyote Gen1
Posts: 72
|
|
Not Ranked
Sycraft, what Energy Suspension part number for the bushings did you end up going with? And did you replace both axle and chassis side of the lower control arms?
__________________
Mark
|
09-01-2022, 08:45 PM
|
|
CC Member
|
|
|
Join Date: Aug 2021
Location: Beaumont,
TX
Cobra Make, Engine: Classic Roadsters, Ford coyote Gen1
Posts: 72
|
|
Not Ranked
Thanks, that's the part # I came across too, and the info on the smaller bushings.
__________________
Mark
|
12-06-2022, 03:44 PM
|
|
CC Member
|
|
|
Join Date: Aug 2021
Location: Beaumont,
TX
Cobra Make, Engine: Classic Roadsters, Ford coyote Gen1
Posts: 72
|
|
Not Ranked
These might help someone out down the road who is looking to upgrade his/her rear suspension bushings. Just order the parts you need from any Energy Suspension seller.
part #, 15.10.08.39 sleeves - (4)
part #, 2061 bushings - (8)
$74.51
__________________
Mark
|
12-06-2022, 05:21 PM
|
|
CC Member
|
|
|
Join Date: Nov 2009
Location: Edmond,
Ok
Cobra Make, Engine: Classic Roadsters
Posts: 628
|
|
Not Ranked
What is the OD of the control arm bushing?
I ordered the recommended rubber bushings and they were a different size then what I have from Classic.
Maybe CR1 is different than CR2 I’m not sure.
__________________
Chaney Shores Studio
Last edited by sunman; 12-06-2022 at 05:24 PM..
|
12-06-2022, 09:14 PM
|
 |
CC Member
|
|
|
Join Date: Feb 2021
Cobra Make, Engine: ford 302
Posts: 290
|
|
Not Ranked
Quote:
Originally Posted by sunman
What is the OD of the control arm bushing?
I ordered the recommended rubber bushings and they were a different size then what I have from Classic.
Maybe CR1 is different than CR2 I’m not sure.
|
the factory bushing is moog sb340 encased in a metal sleeve, its not just a bushing. I have a set of the rubber ones in the garage.
Last edited by Sycraft; 12-06-2022 at 09:29 PM..
|
12-06-2022, 11:25 PM
|
|
CC Member
|
|
|
Join Date: Nov 2009
Location: Edmond,
Ok
Cobra Make, Engine: Classic Roadsters
Posts: 628
|
|
Not Ranked
Thanks, it was SB340s I got but looked to be a different size than what’s in arm.
Have you got the actual od of the Energy part?
__________________
Chaney Shores Studio
|
12-07-2022, 05:44 AM
|
|
CC Member
|
|
|
Join Date: Feb 2021
Cobra Make, Engine: ford 302
Posts: 290
|
|
Not Ranked
I do not, they are in car. but with the sleeve pressed out (it was a tight sleeve) the bushings fit with a slight bit of supplied grease and some slight pressure from a vice
|
12-07-2022, 07:00 AM
|
|
CC Member
|
|
|
Join Date: Aug 2021
Location: Beaumont,
TX
Cobra Make, Engine: Classic Roadsters, Ford coyote Gen1
Posts: 72
|
|
Not Ranked
I'll know, hopefully in 3 months what the OD is. That part has been on back order for quite some time now. But the metal sleeves are in stock.
__________________
Mark
|
12-07-2022, 09:10 PM
|
|
CC Member
|
|
|
Join Date: Feb 2021
Cobra Make, Engine: ford 302
Posts: 290
|
|
Not Ranked
Quote:
Originally Posted by markantioch
I'll know, hopefully in 3 months what the OD is. That part has been on back order for quite some time now. But the metal sleeves are in stock.
|
I ordered 2 sets of this, yes some waste as not everything is needed, but available...
https://www.amazon.com/Energy-Suspen.../dp/B000CN781Y |
12-08-2022, 02:06 AM
|
|
CC Member
|
|
|
Join Date: Aug 2021
Location: Beaumont,
TX
Cobra Make, Engine: Classic Roadsters, Ford coyote Gen1
Posts: 72
|
|
Not Ranked
Yes, that thought came to mind after I had placed the order. But I'm piecemealing this together as I'm also sending my trans to Ben Calimer for a stage 2 upgrade.
Not a bad time to do this work, since it's winter time now, and the temps have cooled off into to low to mid 80s. lol
__________________
Mark
|
12-09-2022, 08:54 PM
|
|
CC Member
|
|
|
Join Date: Jul 2021
Location: Denver,
NC
Cobra Make, Engine: Classic Roadsters, 347 stroker
Posts: 116
|
|
Not Ranked
I am sorry, but I can’t find records of the bushings I bought. They are Energy Suspension bushings. What I did was use a micrometer and measured the exact width of the mounting point on the frame. Then measured the ID of the swing arm, then the width of the swing arm hole. This gave me the three most important measurements to get a comparable bushing. The inner sleeve and bolt size is going to be bigger, but that just meant drilling out the holes in the frame, which was fine. I found just by going on the Energy Suspension website the closest size. It fit perfectly. The bushings did not exactly touch each other when pressed into the swingarm, but was perfect as it left a space to inject grease through the grease fitting. They are perfect. Just match up the size of what you have and it will be fine. The original bushing had a steel sleeve that was pressed into the swingarm. These do not have that. Just an internal sleeve for the bolt to slide into. Don’t forget to coat the bolt with antisieze!!
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 11:39 AM.
Links monetized by VigLink
|
Linear Mode
