Club Cobra

Club Cobra (http://www.clubcobra.com/forums/)
-   Coupe Talk (http://www.clubcobra.com/forums/coupe-talk/)
-   -   coupe info (http://www.clubcobra.com/forums/coupe-talk/102246-coupe-info.html)

snakebite8 01-22-2010 07:27 AM
coupe info
 
hello new to this forum. i was looking into building a coupe daytona and i was wondering if there was a kit that i could buy that uses a fox body mustang as a donor car. i seen them used on the ac cobra kits but never on a daytona. they kit the body of the mustang and use the floor and frame and connect the fiberglass kit to it

Ozgur_Tan 01-22-2010 07:29 AM
welcome to forum
and take a look to FFR 65 coupe
http://www.factoryfive.com/coupehome.html

snakebite8 01-22-2010 08:05 AM
i think you just use a donor car for the wiring and engine and trans rear. not the floor and frame.

Woodz428 01-22-2010 02:31 PM
Quote:
Originally Posted by snakebite8 (Post 1021092)
i think you just use a donor car for the wiring and engine and trans rear. not the floor and frame.
I don't have an FFR, but did look into them about a decade ago. I believe they use the drivetrain and suspension as well as the harness and gauges in the basic kit. It would be easier to build a frame than attempt to use the uinibody Fox car as any basis. I think the intention was to use a wrecked car that had all the mechanicals intact...pretty easy to do with the crushable cars currently being produced.
There is local guy that has one he is building( or has been for about 4 years) one. But I have no room to talk, I still haven't assembled the 428 for our SPF MKIII. The Coupe runs nice though :LOL:

snakebite8 01-23-2010 05:25 AM
i was watching kit an autobody experience and they took and fox mustang and cut the body off the frame and took the cobra body and put it together. thats why i am just trying to see if they anything like that for the coupe

Ozgur_Tan 01-23-2010 05:47 AM
everything is possible
1965 Mustang fastback outter skin with 2003 SVT Cobra powertrain & interior
http://www.sn65.com/SN65%20story.htm

Quote:
Originally Posted by snakebite8 (Post 1021362)
i was watching kit an autobody experience and they took and fox mustang and cut the body off the frame and took the cobra body and put it together. thats why i am just trying to see if they anything like that for the coupe

Woodz428 01-23-2010 06:13 AM
Quote:
Originally Posted by snakebite8 (Post 1021362)
i was watching kit an autobody experience and they took and fox mustang and cut the body off the frame and took the cobra body and put it together. thats why i am just trying to see if they anything like that for the coupe
They don't actually have a frame, so that would be pretty hard to do. they do have subframes that bolt on. But I think I may have said earlier, it would be easier to build a custom frame than attempt to make a unibody car have one.They may have cut it apart to make it easier, but I'd have to see them use the undercarriage before I'd believe they used the frame. I grafted a Fox chassis under a 1940 Desoto years ago and it was very time consuming, however I wasn't attempting to mount a 'glass body on an otherwise flimsy foundation. Without the body the chassis would not only need cut in length it would need and enormous amount of extra structure to make it ridgid. Then there is the width. That's why I suspect that you are referring to an FFR car, which uses the underpinnings but discard the shell.

snakebite8 01-23-2010 12:01 PM
yea that is a good point. the amount of time to make the floor strong enough and the fact the body is fiberglass, i would have to just about make a new frame and floor pan. so in truth just buy a kit from like ffr would be easier and alot less work, and maybe even cheaper.

Bryan Anderson 01-23-2010 01:21 PM
B&B coupe
 
The B&B coupe will allow you to use the engine trans, rear end, all of the rest is supplied by B&B and Is assembled you can see the info at www.bandbroadster.com

Woodz428 01-23-2010 02:18 PM
Bryan, what type of windshield is used in your GT45??

snakebite8 01-24-2010 03:06 PM
thanks for the info everyone. little off the topic but is anyone going to make a kit from the concept car gr-1 that ford made? i know its a modern daytona coupe concept


All times are GMT -7. The time now is 08:10 PM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: