Club Cobra Keith Craft Racing  

Go Back   Club Cobra > Manufacturers, Engine Builders, tools, and parts. > ERA---Speak with Bob Putnam

Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
MMG Superformance
December 2024
S M T W T F S
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31        

Kirkham Motorsports

Like Tree18Likes

Reply
 
LinkBack Thread Tools Display Modes
  #101 (permalink)  
Old 05-28-2019, 02:04 PM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 22,005
Not Ranked     
Default

Quote:
Originally Posted by ACHiPo View Post
An update from yesterday. The problem is not fixed. When I turned the ignition "ON" yesterday, no ignition light. Checked fuse 3 and sure enough it was blown. Replaced the fuse with a 15A one and it blew as well. Changed the wiring back to Bob's recommended configuration eliminating the stator connection on the alternator, removing the "I" spade from the VR, and jumpering the A and S spades on the VR. The pink wire is still disconnected from the fuel sender. The charging works again, but of course no tach or anything else on the ignition circuit.
And with all that disconnected, if you put a fuse in #3 it still blows?
Reply With Quote
  #102 (permalink)  
Old 05-28-2019, 06:03 PM
hauss's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2018
Location: Lodi, CA
Cobra Make, Engine: 427 manowar forged crank roller rockers . BIG CAM.
Posts: 785
Not Ranked     
Default Ideal circuit Tracer

If you would like, I would let you borrow my tester, it is a very high quality unit I paid over 900$ for. You may use it as long as you would like. Met you at the restaurant a year or so ago and you took me for a ride in your superformance. There are instructions in the case and you will need AA and 9v batteries Hope this helps you.
Reply With Quote
  #103 (permalink)  
Old 05-28-2019, 06:36 PM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 22,005
Not Ranked     
Default

Quote:
Originally Posted by hauss View Post
If you would like, I would let you borrow my tester, it is a very high quality unit I paid over 900$ for. You may use it as long as you would like. Met you at the restaurant a year or so ago and you took me for a ride in your superformance. There are instructions in the case and you will need AA and 9v batteries Hope this helps you.
I vote "Yes."
Reply With Quote
  #104 (permalink)  
Old 05-28-2019, 11:16 PM
ACHiPo's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Oct 2016
Location: Pleasanton, CA
Cobra Make, Engine: ERA 824 with 470 FE BBM street 427
Posts: 550
Not Ranked     
Default

Quote:
Originally Posted by patrickt View Post
And with all that disconnected, if you put a fuse in #3 it still blows?
Haven’t tested that yet.
Reply With Quote
  #105 (permalink)  
Old 05-28-2019, 11:18 PM
ACHiPo's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Oct 2016
Location: Pleasanton, CA
Cobra Make, Engine: ERA 824 with 470 FE BBM street 427
Posts: 550
Not Ranked     
Default

Quote:
Originally Posted by hauss View Post
If you would like, I would let you borrow my tester, it is a very high quality unit I paid over 900$ for. You may use it as long as you would like. Met you at the restaurant a year or so ago and you took me for a ride in your superformance. There are instructions in the case and you will need AA and 9v batteries Hope this helps you.
John,
I’m interested in the tester if it will help find a short. Are you coming to Cobra Day?

Evan
Reply With Quote
  #106 (permalink)  
Old 05-28-2019, 11:34 PM
hauss's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2018
Location: Lodi, CA
Cobra Make, Engine: 427 manowar forged crank roller rockers . BIG CAM.
Posts: 785
Not Ranked     
Default

Sent you a p.m. Yes the tester is a high quality tester just read all the instructions Play with it all you want keep it as long as you need.
Reply With Quote
  #107 (permalink)  
Old 05-29-2019, 06:24 AM
ACHiPo's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Oct 2016
Location: Pleasanton, CA
Cobra Make, Engine: ERA 824 with 470 FE BBM street 427
Posts: 550
Not Ranked     
Default

John,
Thanks again. Responded to your PM. I'm curious what kind of tester it is and how it works.

Evan
Reply With Quote
  #108 (permalink)  
Old 05-29-2019, 10:32 AM
hauss's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2018
Location: Lodi, CA
Cobra Make, Engine: 427 manowar forged crank roller rockers . BIG CAM.
Posts: 785
Not Ranked     
Default

NO thanks needed, you are a good man. I emailed you some pictures . I have not forgotten my promise about breakfast so I will make it up to you and bring you the tester.
Reply With Quote
  #109 (permalink)  
Old 05-29-2019, 12:54 PM
ACHiPo's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Oct 2016
Location: Pleasanton, CA
Cobra Make, Engine: ERA 824 with 470 FE BBM street 427
Posts: 550
Not Ranked     
Default

That Ideal tester looks very cool. Not sure it's small enough to troubleshoot my car wiring loom, though?
Reply With Quote
  #110 (permalink)  
Old 05-29-2019, 01:05 PM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 22,005
Not Ranked     
Default

Quote:
Originally Posted by ACHiPo View Post
That Ideal tester looks very cool. Not sure it's small enough to troubleshoot my car wiring loom, though?
Fortunately, Fuse #3 does not carry much amperage at all. I know you don't want to but, starting at the far end of the circuit, and then snipping the wire, in stages, until you can run what's left of the circuit without the fuse blowing, and then slowly butt-crimping the wire back until the short re-appears, works every single time, especially with funky intermittent faults that seem to come and go. With wipers running, the heater fan on, and all gauges working, I bet that circuit doesn't pull but five amps. For something like that, a butt-crimped line will work just as well as a brand new wire, and no one will know the difference. (It's what I would do, and then heat-shrink the butt-crimps and they'll look OEM, not that anyone will every be looking at them.)
Gaz64 likes this.
Reply With Quote
  #111 (permalink)  
Old 05-29-2019, 08:03 PM
hauss's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2018
Location: Lodi, CA
Cobra Make, Engine: 427 manowar forged crank roller rockers . BIG CAM.
Posts: 785
Not Ranked     
Default

Dropped off the tester today .Hope it is useful . IT has many functions and comes with a amp meter It is a Ideal suretrace open/closed circuit tracer #61-957
ACHiPo likes this.
Reply With Quote
  #112 (permalink)  
Old 05-30-2019, 05:53 AM
CC Member
Visit my Photo Gallery

 
Join Date: Nov 2003
Location: New Britain, CT
Cobra Make, Engine: Size 10 Feet
Posts: 3,015
Not Ranked     
Default

Quote:
Originally Posted by ACHiPo View Post
That Ideal tester looks very cool. Not sure it's small enough to troubleshoot my car wiring loom, though?
Evan,

I'm hoping the cause is in between the voltage regulator and the ignition warning light. What I will do is give you a replacement for everything in that circuit, from regulator to light to power. The leads will be long enough to test before a permanent install parallel to the original leads.

Bob P.
ACHiPo likes this.
Reply With Quote
  #113 (permalink)  
Old 05-30-2019, 07:14 AM
ACHiPo's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Oct 2016
Location: Pleasanton, CA
Cobra Make, Engine: ERA 824 with 470 FE BBM street 427
Posts: 550
Not Ranked     
Default

Thanks Bob and John! Need to focus on getting the car ready for Cobra Day, but hope to get back to troubleshooting Sunday.
Reply With Quote
  #114 (permalink)  
Old 09-08-2019, 04:51 PM
ACHiPo's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Oct 2016
Location: Pleasanton, CA
Cobra Make, Engine: ERA 824 with 470 FE BBM street 427
Posts: 550
Not Ranked     
Default

I'm finally getting back to troubleshooting.

I ordered one of these:
https://www.realfixesrealfast.com/short-finder.html

Basically an automatically resetting 10A circuit breaker with a Gauss meter to detect current.

I clipped the CB to a test light to have a visual indication of the breaker tripping and replaced fuse three with the set up.

I reconnected the stator and VR to the circuit, but left the pink wire from the dash to the fuel sender disconnected.

When I turned the key to ACC, the test light lit, but the ignition light did not. Also, the CB did not trip, suggesting it's either way more than 10A (15A fuses blow in fuse 3), or faulty. I turned the key to "on", and again no ignition light and no CB trip. I started the car. The ammeter was charging, but no tach. The test light remained lit, although it seemed a bit dimmer than when the key was in the on or acc position.

I reconnected the pink wire to the fuel sender and no change--no acc or on ignition light, car started fine, and ammeter worked. I disconnected the pink wire again.

I inserted a 10 Ohm shunt resistor in parallel with the ignition bulb Bob sent me. The purpose, according to Bob, is to add current to the VR energizer circuit guaranteeing actuation.

I removed the CB from fuse 3 and repeated Patrick's test with the auto-reset CB + test light jumper between the ACC terminal and the outer (double green wire) tab on the ignition light. Both the ignition light and test light lit (although dimly).

I put everything back together, put a fuse in #3, turned the key to acc, and the ignition light illuminated. Turning the key to "on" and the ignition light still lit. Starting the engine, the tach worked, the gas gauge moved off E, the ignition light was not on. Everything seemed to be working correctly.

I reconnected the pink wire to the fuel sender and the 15A fuse 3 blew. I disconnected the pink wire, replaced the fuse with the CB and test light. No ignition light, no tach. Started the engine, the CB did not trip, the tach didn't move, the ammeter showed discharging, but not charging.

I'm now thinking I have two issues: 1) a ground loop or short in the pink wire to the fuel sender, and 2) an intermittent VR.

Thoughts?
Attached Images
 
Reply With Quote
  #115 (permalink)  
Old 09-08-2019, 05:14 PM
DanEC's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2009
Location: Little Rock area, AR
Cobra Make, Engine: ERA Street Roadster #782 with 459 cu in FE KC engine, toploader, 3.31
Posts: 4,521
Not Ranked     
Default

Thoughts - man, you have a lot of patience and perseverance Evan. I'm no help but hope you get it figured out before long.
__________________
ERA 782 Running
https://www.youtube.com/watch?v=Cfge...b1-77fqwFRu7c]
Reply With Quote
  #116 (permalink)  
Old 09-08-2019, 05:22 PM
ACHiPo's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Oct 2016
Location: Pleasanton, CA
Cobra Make, Engine: ERA 824 with 470 FE BBM street 427
Posts: 550
Not Ranked     
Default

Dan,
Thanks. I've basically taken a 3 month hiatus. Just now getting back to it. The fact that it almost kinda works makes me think I'm definitely gaining on it. As the joke about the optimistic kid goes, "there's got to be a REALLY COOL PONY under a pile of poo this big!!!"

Last edited by ACHiPo; 09-08-2019 at 05:40 PM..
Reply With Quote
  #117 (permalink)  
Old 09-08-2019, 07:24 PM
Gaz64's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2008
Location: Brisbane, QLD
Cobra Make, Engine:
Posts: 2,797
Not Ranked     
Default

Quote:
Originally Posted by ACHiPo View Post
I'm finally getting back to troubleshooting.

I clipped the CB to a test light to have a visual indication of the breaker tripping and replaced fuse three with the set up.

When I turned the key to ACC, the test light lit, but the ignition light did not. Also, the CB did not trip, suggesting it's either way more than 10A (15A fuses blow in fuse 3), or faulty.

Thoughts?
A 10A CB will never trip with a test light in series, unless the lamp is 120w.

Gary
Reply With Quote
  #118 (permalink)  
Old 09-08-2019, 11:03 PM
ACHiPo's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Oct 2016
Location: Pleasanton, CA
Cobra Make, Engine: ERA 824 with 470 FE BBM street 427
Posts: 550
Not Ranked     
Default

Quote:
Originally Posted by Gaz64 View Post
A 10A CB will never trip with a test light in series, unless the lamp is 120w.

Gary
Gary,
Why do you say that? I could understand if the lamp was in parallel with the breaker, but in series amps is amps. What am I missing?

Evan
Reply With Quote
  #119 (permalink)  
Old 09-09-2019, 10:36 AM
CC Member
Visit my Photo Gallery

 
Join Date: Aug 2013
Location: Los Gatos, CA
Cobra Make, Engine: ERA #3014; 331 CID SBF
Posts: 86
Not Ranked     
Default

I didn't have any of your other symptoms, but I recently discovered that the white and pink wires were reversed at the fuel sender in #3014. Since my car has SW gauges and no requirement for the pink hot wire, this means:

1. fuel gauge was inop because the white sender wire was no-connect at the sender; and

2. the 30-240 ohm fuel-level rheostat in the tank was functioning as a 0.6-5 watt heater because it had +12V applied to it via the pink wire.

Bill
Reply With Quote
  #120 (permalink)  
Old 09-09-2019, 10:39 AM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 22,005
Not Ranked     
Default

Quote:
Originally Posted by ACHiPo View Post
Gary,
Why do you say that? I could understand if the lamp was in parallel with the breaker, but in series amps is amps. What am I missing?

Evan
Let's not get side tracked on that. Gary is taking 12v and multiplying by 10a and saying that you have to have 120 watts to blow the circuit breaker. Instead, I think you should try this approach: 1) Tape off the pink wire that goes to the fuel sender. We're not going to 'untape' it, for any reason, until we have all other charging system issues fixed. 2) Put a fresh, known to be good, fuse in slot #3 and put the CB tester and test light on the floor. 3) Turn the key first to the ON position, but do not start the car, and observe the charging light on the dash (should be on). If it is not on, stop the testing and report back. If it is on, start the car and see if the light goes out and the ammeter gauge is working properly. Report back.
ACHiPo likes this.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 08:59 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink