 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
|
November 2024
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
|
|
|
1 |
2 |
| 3 |
4 |
5 |
6 |
7 |
8 |
9 |
| 10 |
11 |
12 |
13 |
14 |
15 |
16 |
| 17 |
18 |
19 |
20 |
21 |
22 |
23 |
| 24 |
25 |
26 |
27 |
28 |
29 |
30 |
|
|
CC Advertisers
|
|
05-05-2006, 12:01 PM
|
 |
CC Member
|
|
|
Join Date: May 2004
Location: Palm Coast,
FL
Cobra Make, Engine: Shelby American CSX 4241 - authentically built
Posts: 2,573
|
|
Not Ranked
FE pilot bushing/bearing
Might be putting my motor in soon, and I had a question about the pilot bushing.... I am using a Tremec trans on the back of my 390. Do I still use a standard OEM toploader FE pilot bushing, or is there a special one I need to get? Also, anyone have a preference between a bushing and a bearing?
Thanks!
__________________
Sal Mennella
CSX 4241, KMP 357 - sold and missed, CSX 4819 - cancelled, FFR 5132 - sold
See my car at CSXinfo.net here >> CSX 4241
|
-
Advertising
05-05-2006, 04:34 PM
|
|
CC Member
|
|
|
Join Date: Mar 2002
Cobra Make, Engine:
Posts: 302
|
|
Not Ranked
Same bushing.
And I prefer the bushing over the bearing. A bushing can wear out, but a bearing can have a catastrophic failure which doesn't end up very pretty.
Tom
|
05-05-2006, 04:42 PM
|
|
CC Member
|
|
|
Join Date: May 2004
Location: Palm Coast,
FL
Cobra Make, Engine: Shelby American CSX 4241 - authentically built
Posts: 2,573
|
|
Not Ranked
Thanks Tom, that's just the info I was looking for.
__________________
Sal Mennella
CSX 4241, KMP 357 - sold and missed, CSX 4819 - cancelled, FFR 5132 - sold
See my car at CSXinfo.net here >> CSX 4241
|
05-05-2006, 05:38 PM
|
 |
CC Member
|
|
|
Join Date: Dec 2000
Location: Broken Arrow. OK ( South Tulsa), USA,
OK
Cobra Make, Engine: 66 COBRA FE 427 /4SP. (HCS Coupe w/ 408 Stroker and TKO 600 -sold)
Posts: 5,595
|
|
Not Ranked
Most FE's I have seen run the standard Brass Bushing. That is what I am running with my Toploader and Dean Lampe ran with his TKO 600.
Clois
__________________
Sunshine, Asphalt and no stop signs...Perfect
"Let's roll"
"Be part of Something Good
......Leave Something Good Behind!"
from CD "Long Road Out of Eden"
|
05-05-2006, 06:25 PM
|
|
CC Member
|
|
|
Join Date: Dec 2001
Location: Louisville,
KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,415
|
|
Not Ranked
I'm running a bushing also with my Toploader. Bearings seem to fit a little more tighter....and I think that if your bellhousing isn't perfectly aligned, it could complicate things worse.
|
05-05-2006, 09:08 PM
|
 |
CC Member
|
|
|
Join Date: Sep 2001
Location: Tulsa,
OK
Cobra Make, Engine: SPF 148 with 427 SO
Posts: 629
|
|
Not Ranked
this thread just killed me. ask clois, I can't even talk about it!
Buzz
|
05-06-2006, 07:46 PM
|
 |
CC Member
|
|
|
Join Date: Jul 2004
Location: Alpharetta,
GA
Cobra Make, Engine: ERA #414 427 s/o w. Shelby Aluminum heads, Edelbrock Performer RPM Intake, Mighty Demon 750, Tremec TKO 600
Posts: 714
|
|
Not Ranked
Please - do tell Clois or Buzz. I just installed a TKO and used a bearing. Am I setting myself up for trouble?
|
05-06-2006, 09:05 PM
|
|
CC Member
|
|
|
Join Date: Jun 2003
Cobra Make, Engine: ERA 427 w/496 Side Oiler, roller, dual quads
Posts: 417
|
|
Not Ranked
The only time the bearing/bushing does anything besides keep the front of the trans shaft in line is when you have your foot on the clutch. Otherwise the front trans shaft and crankshaft are turning at the same speed. I personally see little difference between the two, but I use the bearing.
Dan
__________________
Do you know why they call it "PMS"? Because "Mad Cow Disease" was taken. --Unknown, presumed deceased
|
05-08-2006, 03:48 PM
|
|
CC Member
|
|
|
Join Date: Sep 2001
Location: Tulsa,
OK
Cobra Make, Engine: SPF 148 with 427 SO
Posts: 629
|
|
Not Ranked
I just realized reading this that I did not install either and the motor has to come back out....OUCH!
|
05-08-2006, 04:01 PM
|
|
CC Member
|
|
|
Join Date: Dec 2001
Location: Louisville,
KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,415
|
|
Not Ranked
You can't drop the tranny under the car and install it with the engine in?
|
05-08-2006, 04:19 PM
|
|
CC Member
|
|
|
Join Date: Sep 2001
Location: Tulsa,
OK
Cobra Make, Engine: SPF 148 with 427 SO
Posts: 629
|
|
Not Ranked
in a SPF, you have to pull the trans tunnel to get the trans out, or you pull the engine. Since I have some oil leak issues again to fix and some gasket work..and now I am a pro at pulling that bad boy, the engine is the option I am gonna take. but man, am I hacked at myself! a few days and good as new. I am just glad that I remembered before the trans exploded.
Buzz |
05-17-2006, 10:27 AM
|
|
CC Member
|
|
|
Join Date: Sep 2001
Location: Tulsa,
OK
Cobra Make, Engine: SPF 148 with 427 SO
Posts: 629
|
|
Not Ranked
anyone have a part number for the bushing. same as the one for a 390?
Buzz
|
05-17-2006, 10:36 AM
|
|
CC Member
|
|
|
Join Date: Dec 2001
Location: Louisville,
KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,415
|
|
Not Ranked
Buzz, I got mine from Napa. I asked for a pilot bushing for a 69 Mustang.
BRG B50HD
|
05-17-2006, 01:34 PM
|
|
CC Member
|
|
|
Join Date: Mar 2002
Cobra Make, Engine:
Posts: 302
|
|
Not Ranked
I think ALL the FE's use the same bushing. But definitely if you asked for ANY 390 bushing it'd be right.
Tom
|
05-17-2006, 01:53 PM
|
|
CC Member
|
|
|
Join Date: Sep 2001
Location: Tulsa,
OK
Cobra Make, Engine: SPF 148 with 427 SO
Posts: 629
|
|
Not Ranked
yeap...you guys are right on the money once again. thanks
Buzz
|
05-26-2006, 12:44 PM
|
 |
CC Member
|
|
|
Join Date: Nov 2003
Location: Fresno,
CA
Cobra Make, Engine: Shelby CSX 4766 (Vegas Built) with 482 Aluminum Pond motor
Posts: 814
|
|
Not Ranked
bearing
I am running a sealed bearing. Keep in mind that these are not high milage cars! Also the majority of auto manufactures use a bearing currently. But you have to run one or the other.
__________________
Morgan LeBlanc
Fresno CA
|
05-26-2006, 01:27 PM
|
|
CC Member
|
|
|
Join Date: Sep 2001
Location: Tulsa,
OK
Cobra Make, Engine: SPF 148 with 427 SO
Posts: 629
|
|
Not Ranked
|
11-27-2007, 04:40 PM
|
|
CC Member
|
|
|
Join Date: Jun 2005
Location: Henderson,
NV
Cobra Make, Engine: Superformance
Posts: 64
|
|
Not Ranked
Pilot Bearing
Having a hard time locating a pilot bearing for a 427 FE (most parts stores only carry the bushing). Does anyone have a part # for the bearing type?
Quote:
|
Originally Posted by Carnut427
The only time the bearing/bushing does anything besides keep the front of the trans shaft in line is when you have your foot on the clutch. Otherwise the front trans shaft and crankshaft are turning at the same speed. I personally see little difference between the two, but I use the bearing.
Dan
|
|
11-27-2007, 06:57 PM
|
|
Senior Club Cobra Member
|
|
|
Join Date: Nov 2006
Location: Charleston,
WV
Cobra Make, Engine: SPF 2592, Shelby alum. 527
Posts: 325
|
|
Not Ranked
Quote:
|
Originally Posted by MCOULTER
Having a hard time locating a pilot bearing for a 427 FE (most parts stores only carry the bushing). Does anyone have a part # for the bearing type?
|
I used a Federal-Mogul 303SS. Sealed ball bearing with metal shields.
Rodger |
11-29-2007, 04:46 PM
|
|
CC Member
|
|
|
Join Date: Jun 2005
Location: Henderson,
NV
Cobra Make, Engine: Superformance
Posts: 64
|
|
Not Ranked
FYI...It ended up being Napa part 6303-2ZJ (manufactured by SKF).
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 06:57 AM.
|
Linear Mode
