Keith Craft Inc.- We service what we sell!!! Check out our Cobra engines!!! We build high performance racing engines and components for the fast pace strip racing industry as well as daily drivers who want to be FIRST!!!

FE Forums sponsored by Keith Craft Inc.


Go Back   Club Cobra > Engine Building, Tuning, and Induction > FE TALK

Welcome to Club Cobra!  The World's largest non biased Shelby Cobra related site!

  •  » Representation from nearly all Cobra/Daytona/GT40 manufacturers
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and nearly 1 million posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

MMG Superformance
Nevada Classics
Main Menu
Nevada Classics
Nevada Classics
MMG Superformance
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
Keith Craft Racing
MMG Superformance
December 2024
S M T W T F S
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31        

Kirkham Motorsports

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #1 (permalink)  
Old 07-15-2006, 03:13 PM
lineslinger's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jan 2004
Location: St. Louis, Mo.
Cobra Make, Engine: 427 S.O. Dual Quad / Cobra undecided
Posts: 1,380
Not Ranked     
Default Long term engine storage

I've got my engine ready to install, but at this time no car to install it in.
The motor has been fired up on a startup stand and has a little less than an hour of run-in time on it, mostly to make sure the cam got some proper break-in (inner springs were not installed for run-in) and the leak factor dealt with.
So all is now good with the motor. Now it sits on a stand in my garage. I have installed the inner springs and loosened the valve train to where it is sitting loosely on the rocker studs with zero tension on the rocker arms or valves.
The original 'run-in" oil is still in it as is the the oil filter.
I put magnets at the drain plug area of oil pan as well as the bottom of the oil filter.
Can someone offer some advice as to what my next steps should be? Its going to be awhile (months) before I am able to start this motor again but I am trying to avoid any storage/sitting problems during downtime.
thanks in advance
Mark
Reply With Quote
  #2 (permalink)  
Old 07-15-2006, 04:27 PM
vettestr's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Dec 2001
Location: Glendale, AZ.
Cobra Make, Engine: Cobray-C3, The 60's body lines on todays chassis technology
Posts: 2,302
Not Ranked     
Default

Well first it a shame not to be able to use it NOW. For our spare race engines we would back off the valve rockers so it does not sit with springs compressed and valves open. A squirt of oil in each cylinder and then replace the spark plugs. The plugs in bottom of block near pan rail are replaced with petcocks so coolant can be drained from block easily.
I might be tempted to rotate the crank each month or so just to keep seals moist. Compression will leak past rings without valves open as you bar it over. You could also give it to a buddy to run the dog snot out of it until you are ready for it.
__________________
Jeff Classic
Manufacturer of the Cobray-C3
www.cobrasnvettes.com
Reply With Quote
  #3 (permalink)  
Old 07-15-2006, 05:57 PM
d_ford's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2003
Location: Nelsonville, OH
Cobra Make, Engine: CSX4000, Shelby aluminum 496 ci FE
Posts: 417
Not Ranked     
Default

I was told by an old ford engine builder to squirt marvel mystery oil into each cylinder and turn it over by hand prior to long term storage. It seemed to work fine, no problems after storage.
__________________
Doug
CSX4761
ERA #115 - sold
ERA #002 - sold
07 GT500
66 GT350 tribute
70 Mach 1
65 Comet gasser
Reply With Quote
  #4 (permalink)  
Old 07-15-2006, 06:56 PM
wtm442's Avatar
Beam Me Up Scottie
Visit my Photo Gallery

 
Join Date: Aug 2004
Location: Squantum (part of Quincy), MA
Cobra Make, Engine: SPF1049 Titanium w/black stripes, 351W with Trick Flow Heads, Tremec 3550
Posts: 7,592
Send a message via MSN to wtm442
Not Ranked     
Lightbulb

If its only 2 months, get a desiccant bag - throw it in a heavy duty contractor bag and seal it around the complete engine.

Any longer than 2 months, add oil to cylinders, do bag trick above and turn motor over by hand every other month.
__________________
Warren
'Liberals are maggots upon the life of this planet and need to get off at the next rotation.' (Jamo 2008)
Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 07:50 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy