 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
|
|
|
1 |
2 |
| 3 |
4 |
5 |
6 |
7 |
8 |
9 |
| 10 |
11 |
12 |
13 |
14 |
15 |
16 |
| 17 |
18 |
19 |
20 |
21 |
22 |
23 |
| 24 |
25 |
26 |
27 |
28 |
29 |
30 |
|
|
CC Advertisers
|
|
01-10-2009, 07:08 PM
|
 |
Ouch Ouch Hot Sand
|
|
|
Join Date: Jul 2003
Location: Daytona Beach,
FL
Cobra Make, Engine: Street Beasts w/302 Twin Turbocharged....Under Construction!!
Posts: 1,796
|
|
Not Ranked
Help with Upper Intake Manifold
I have an upper with the following code......RF-F32E-9426-CB......any help with this code would be greatly appreciated. Thanks, Earl
__________________
Safe Flyin, errrrr Drivin, Earl
|
01-10-2009, 08:13 PM
|
 |
CC Member
|
|
|
Join Date: May 2008
Location: San Jose CA,
CA
Cobra Make, Engine: SPF_R_/BRG/FRBoss302/327CI/FordEFI/Under_Car_Exh/
Posts: 2,523
|
|
Not Ranked
are you sure that is not F3ZE or F3SE >?
-9426 is a Ford intake number, but the prefix is typo'd i think.
__________________
Steve SPF 2734 MK3 / Brock Coupe #54- panavia.com
|
01-10-2009, 08:27 PM
|
|
Ouch Ouch Hot Sand
|
|
|
Join Date: Jul 2003
Location: Daytona Beach,
FL
Cobra Make, Engine: Street Beasts w/302 Twin Turbocharged....Under Construction!!
Posts: 1,796
|
|
Not Ranked
Quote:
|
are you sure that is not F3ZE or F3SE >?
|
Oppppppppppsssssssssss, sorry, it is F3ZE....thanks, Earl
__________________
Safe Flyin, errrrr Drivin, Earl
|
01-10-2009, 09:13 PM
|
 |
CC Member
|
|
|
Join Date: Mar 2007
Location: Creedmoor,
TX
Cobra Make, Engine: FFR3542K, 347 C. I., EFI, T-5, Miata Front Sway Bar, 3 Link, Red with White Stripes
Posts: 1,161
|
|
Not Ranked
It should be a Cobra intake. It should have offset intake runners. Better than the stock HO intake.
I hope these pictures come out.
Steve  |
01-10-2009, 09:17 PM
|
|
CC Member
|
|
|
Join Date: Mar 2007
Location: Creedmoor,
TX
Cobra Make, Engine: FFR3542K, 347 C. I., EFI, T-5, Miata Front Sway Bar, 3 Link, Red with White Stripes
Posts: 1,161
|
|
Not Ranked
|
01-10-2009, 09:26 PM
|
|
Ouch Ouch Hot Sand
|
|
|
Join Date: Jul 2003
Location: Daytona Beach,
FL
Cobra Make, Engine: Street Beasts w/302 Twin Turbocharged....Under Construction!!
Posts: 1,796
|
|
Not Ranked
Okay, great, now next two questions, the little pipe sticking out to the left and below the 8 intake holes in the picture, where does it go to and the T fitting thats supposed to be in the bottom left corner, where does it go??
__________________
Safe Flyin, errrrr Drivin, Earl
|
01-10-2009, 11:58 PM
|
|
CC Member
|
|
|
Join Date: May 2008
Location: San Jose CA,
CA
Cobra Make, Engine: SPF_R_/BRG/FRBoss302/327CI/FordEFI/Under_Car_Exh/
Posts: 2,523
|
|
Not Ranked
so you may need things drawn from manifold vacuum.
1. Power Brake Boosters.
2. PCV valves
the middle one is used as PCV, the fitting on the corner can be used for a PBB.
if you are not using a PBB you can cap it off with a NPT plug.
I always advise the running of a PCV valve, it reduces crank case acids and keep unburned gasoline vapors from messing with things, like bearings.
--Steve
__________________
Steve SPF 2734 MK3 / Brock Coupe #54- panavia.com
Last edited by PANAVIA; 01-12-2009 at 01:13 AM..
|
01-13-2009, 02:04 PM
|
|
Ouch Ouch Hot Sand
|
|
|
Join Date: Jul 2003
Location: Daytona Beach,
FL
Cobra Make, Engine: Street Beasts w/302 Twin Turbocharged....Under Construction!!
Posts: 1,796
|
|
Not Ranked
I am not running a pbb so is there any other reason not to cap off the corner hole?? Also, the one underneath, you say it is for PCV, so the hose runs from there to the vavle in the rear of the lower intake??
Thanks, Earl
__________________
Safe Flyin, errrrr Drivin, Earl
|
01-14-2009, 02:00 AM
|
|
CC Member
|
|
|
Join Date: May 2008
Location: San Jose CA,
CA
Cobra Make, Engine: SPF_R_/BRG/FRBoss302/327CI/FordEFI/Under_Car_Exh/
Posts: 2,523
|
|
Not Ranked
Go ahead and Cap it. -- yes that is correct. dont forget the screen in the lower intake under the PCV.
Steve
__________________
Steve SPF 2734 MK3 / Brock Coupe #54- panavia.com
|
01-18-2009, 10:00 PM
|
|
Ouch Ouch Hot Sand
|
|
|
Join Date: Jul 2003
Location: Daytona Beach,
FL
Cobra Make, Engine: Street Beasts w/302 Twin Turbocharged....Under Construction!!
Posts: 1,796
|
|
Not Ranked
INTAKE Mystery Hole.........LOL
OKAY, sorry for the CRUDDY picture, but its all I could get tonight.....
There is a brass pipe on the left side of the pic, which I assume is the one that goes to the PVC valve.....what is the hole on the right where a fitting screws into??
In seagulls above picture the hole is right below the pipe thats sticking out.........
__________________
Safe Flyin, errrrr Drivin, Earl
|
01-19-2009, 12:05 AM
|
|
CC Member
|
|
|
Join Date: May 2008
Location: San Jose CA,
CA
Cobra Make, Engine: SPF_R_/BRG/FRBoss302/327CI/FordEFI/Under_Car_Exh/
Posts: 2,523
|
|
Not Ranked
need better picture.....
__________________
Steve SPF 2734 MK3 / Brock Coupe #54- panavia.com
|
01-19-2009, 07:44 PM
|
|
Ouch Ouch Hot Sand
|
|
|
Join Date: Jul 2003
Location: Daytona Beach,
FL
Cobra Make, Engine: Street Beasts w/302 Twin Turbocharged....Under Construction!!
Posts: 1,796
|
|
Not Ranked
Hopefully this is better...............
__________________
Safe Flyin, errrrr Drivin, Earl
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 04:33 AM.
Links monetized by VigLink
|
Linear Mode
