Club Cobra - West Coast Cobra hydraulic throwwout bearing

Main Menu

Portal
Forums

Nevada Classics

Advertise at CC

November 2024

S	M	T	W	T	F	S
					1	2
3	4	5	6	7	8	9
10	11	12	13	14	15	16
17	18	19	20	21	22	23
24	25	26	27	28	29	30

CC Advertisers

· Kirkham Motorsports
Superformance
· Finish Line
· Hurricane Motorsports
· Serpent Express
·
· Planet Cobra

· Shell Valley Classic Wheels
· Eight Stack Injection

West Coast Cobra hydraulic throwwout bearing

Discussion Tools

05-18-2021 08:43 AM - permalink

BAsque1

Good morning folks:
By any chance do anyone of you guys have any idea as to the type of throwout bearing installed in our cars equipped with a 427 FE engines? I have a Centerforce Clutch Disk 388184 & centerforce diaphragm with a Dorman 690-032 pilot bushing coupled to a Ford Racing Flywheel M-6375-N427.

When these were installed (2 yedars ago)my mechanic just informed me that the throwout bearing (hydraulic ) was not changed (bad move on his part) now is making a grinding noise (intermittent) shifting is fine and no slipping but the noise comes and goes . So it was diagnosed as a troubled throwout bearing.
Any thoughts anyone?
tks
Lou

05-20-2021 11:49 AM - permalink

kitcarbp

Hey Lou. It could any number of part number combinations. You need to know the pressure plate part number and the hydraulic slave part numbers to narrow down which bearing will fit without removing it. The hydraulic concentric slave cylinder mounted inside the trans has the throw out bearing at the end of the piston. And if the bearing itself is noisy (grinding???) you can apply light pressure to the clutch pedal and maybe influence the noise to confirm it’s the bearing. The fact that it’s shifting fine indicates the slave cylinder is working fine hydraulically. It’s likely 4-5 hrs a of labor and of course a $30 bearing Mine squeaks a little when cold but when warms up it’s quiet but it’s 14 years old. I live with it since it functions but one day it to will get worse.
I couldn’t use Centerforce clutch because the McLeod HTOB interfered with pressure plate centrifugal weights. So I went with all McLeod parts.

05-30-2021 06:50 AM - permalink

BAsque1

I know the Clutch and pressure plate #s , I called Centerforce and they cannot match that to a throwout bearing so I am waiting for my mechanic to give me a time to get it done. I don't want to venture out too far and have the car towed in, the flatbeds in the area are to steep of an angle for the car to clear the sidepipes .
Tks
Lou

All times are GMT -7. The time now is 07:56 PM.

Contact Us - Club Cobra Home - Archive - Top

The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy

Links monetized by VigLink