 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
|
April 2025
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
1 |
2 |
3 |
4 |
5 |
| 6 |
7 |
8 |
9 |
10 |
11 |
12 |
| 13 |
14 |
15 |
16 |
17 |
18 |
19 |
| 20 |
21 |
22 |
23 |
24 |
25 |
26 |
| 27 |
28 |
29 |
30 |
|
|
|
|
|
CC Advertisers
|
|
07-17-2010, 10:52 AM
|
|
CC Member
|
|
|
Join Date: Mar 2003
Location: Fresno,
Ca
Cobra Make & Engine: Kirkham 427
Posts: 140
|
|
1 1/4 inch aluminum T
My project is stopped because I can not find a 1 1/4 inch aluminum T for a water manifold connecting to my webers. Does anybody know where I could find this piece. I do not have the ability to weld aluminum or I would make it myself. Thank you jpfletch@pacbell.net |
07-17-2010, 11:31 AM
|
 |
CC Member
|
|
|
Join Date: Jan 2008
Location: Williamsport,
PA
Cobra Make & Engine: Kellison Stallion 468 FE
Posts: 2,703
|
|
Quote:
Originally Posted by jpfletch1
My project is stopped because I can not find a 1 1/4 inch aluminum T for a water manifold connecting to my webers. Does anybody know where I could find this piece. I do not have the ability to weld aluminum or I would make it myself. Thank you jpfletch@pacbell.net |
try here.....
http://www.mcmaster.com/#aluminum-pipe/=804xfm |
07-17-2010, 01:17 PM
|
 |
CC Member
|
|
|
Join Date: Jul 2005
Location: Bartlett,
Ill
Cobra Make & Engine: Everett-Morrison LS1
Posts: 2,448
|
|
also look at stainless steel pieces
|
07-17-2010, 01:55 PM
|
 |
CC Member
|
|
|
Join Date: Feb 2006
Location: Gore. New Zealand.,
SI
Cobra Make & Engine: DIY Coupe, F/T ,MkIV.
Posts: 808
|
|
I see blue thunder sell this proper piece for SBF, is that what you want one for...or another application.
I was just on the Ford 'Y-Block' site & they have a pic in the SBF Weber manifold section..
__________________
Jac Mac
|
07-17-2010, 02:10 PM
|
 |
CC Member
|
|
|
Join Date: May 2001
Location: California,
Ca
Cobra Make & Engine: NAF 289 Slabside Early Comp Car with 289 Webers and all the goodies. Cancelling the efforts of several Priuses
Posts: 6,592
|
|
What engine are you working with? Is this what you are attempting to create??
[IMG]  [/IMG]
__________________
Rick
As you slide down the Banister of Life, may the splinters never be pointing the wrong way 
Last edited by Rick Parker; 07-17-2010 at 02:14 PM..
|
07-17-2010, 07:13 PM
|
 |
Senior Club Cobra Member
|
|
|
Join Date: Sep 2000
Location: Holderness, NH, US of A,
NH
Cobra Make & Engine: CSX 4772 old iron FE
Posts: 5,499
|
|
I can make it if you can't find it anywhere from the leads given.
|
07-18-2010, 08:03 AM
|
|
CC Member
|
|
|
Join Date: Mar 2003
Location: Fresno,
Ca
Cobra Make & Engine: Kirkham 427
Posts: 140
|
|
Quote:
Originally Posted by Rick Parker
What engine are you working with? Is this what you are attempting to create??
[IMG] [/IMG] |
It is on a 302. I am going to post a photo later today. I have seen your set up before but what are the 4 tubes for ? Thanks Jim |
07-18-2010, 09:27 AM
|
|
CC Member
|
|
|
Join Date: May 2001
Location: California,
Ca
Cobra Make & Engine: NAF 289 Slabside Early Comp Car with 289 Webers and all the goodies. Cancelling the efforts of several Priuses
Posts: 6,592
|
|
This manifold design incorporates a fuel distribution block. Others just run a single line from the pump then in series to each carb. Used on 289 Cobra.
__________________
Rick
As you slide down the Banister of Life, may the splinters never be pointing the wrong way
Last edited by Rick Parker; 07-18-2010 at 01:43 PM..
|
07-18-2010, 12:31 PM
|
|
CC Member
|
|
|
Join Date: Feb 2006
Location: Gore. New Zealand.,
SI
Cobra Make & Engine: DIY Coupe, F/T ,MkIV.
Posts: 808
|
|
From what I understand this is for an ERA GT40?, & these cars per the ERA info have the coolant going from the outlet or T/Stat via this 'Tee' into the bottom of the header tank which appears to be mounted on the RHS firewall-beside #1 plug-. The 'Tee' is mounted between the water outlet & header tank & is also attached to the pipe going fwd to the radiator. Therefore the 'Cobra' type water neck will exit on the wrong side.
JP Fletch also posted this enquiry on GT40's, I was able to attach a dwg on that site, it wont upload here for some reason..
If Im correct he wants a simple single barbed 'Tee' fitting in alloy to suit a hose with 1.25" bore
__________________
Jac Mac
|
07-18-2010, 07:34 PM
|
|
CC Member
|
|
|
Join Date: Mar 2003
Location: Fresno,
Ca
Cobra Make & Engine: Kirkham 427
Posts: 140
|
|
Correct, I could not have said it better myself. Thanks everyone
|
07-19-2010, 09:07 AM
|
|
CC Member
|
|
|
Join Date: Mar 2003
Location: Fresno,
Ca
Cobra Make & Engine: Kirkham 427
Posts: 140
|
|
[ATTACH] 
HELP Here is the fitting I need for my ERA gt40. It is a 1 1/4. Does any one have this or know where to get it. Thanks
|
07-19-2010, 10:17 AM
|
|
CC Member
|
|
|
Join Date: Nov 2003
Location: New Britain,
CT
Cobra Make & Engine: Size 10 Feet
Posts: 3,027
|
|
Have you called ERA (since we make that here?).
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 05:39 PM.
|
Linear Mode
