Go Back   Club Cobra > Club GT40 Areas (MKI - MKII - MKIII - MKIV) > GT40 Talk
User Name
Password
Club Cobra Home Register FAQ For Sale Calendar Today's Posts Journals

MMG Superformance
Nevada Classics
Main Menu
Nevada Classics
Nevada Classics
MMG Superformance
MMG Superformance
Advertise at CC
Banner Ad Rates
Keith Craft Racing
Keith Craft Racing
Keith Craft Racing
MMG Superformance
December 2024
S M T W T F S
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31        

Kirkham Motorsports

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #1 (permalink)  
Old 11-13-2006, 10:20 AM
speed220mph's Avatar
CC Member
Visit my Photo Gallery
 
Join Date: Sep 2002
Location: Hickory, NC
Cobra Make & Engine: ERA 427SC w/427so, ERA GT #2002
Posts: 1,106
Question Front Suspension Shims

Anyone ever have this happen . . . and fix the problem?

Took my ERA GT out for a ride last week and noticed the steering wheel was off center. Upon returning I also noticed an alignment shim laying in the driveway. Putting two and two together, I flipped up the front end and, whoa, all shims were missing from the front of both right-side upper control-arm pivots! There was the reason for the misaligned steering wheel. Wierd because the car didn't pull. Caster had to be off.

Back to the problem: I guess what happened is the pivot bolts loosen just enough to reduce the clamping load on the shims which allowed them to fall out. I now wonder how the shims are clamped between two solid flanges. And from a practical standpoint, I'm also wondering how I can install new shims, then get an Allen wrench into a tight area to loosen and retighten the pivot bolt so they will retain the new shims. Realignment will have to be done. Too bad. It was spot on.

Any suggestions on tools and techniques?
__________________
Tom

"If you can make black marks on a straight from the time you turn out of a corner until the braking point of the next turn, then you have enough HORSEPOWER." Mark Donohue
Reply With Quote
  #2 (permalink)  
Old 11-13-2006, 04:42 PM
CC Member
Visit my Photo Gallery
 
Join Date: Jan 2005
Posts: 15
Default

Can you post some pictures?
Ron
Reply With Quote
  #3 (permalink)  
Old 11-13-2006, 05:46 PM
speed220mph's Avatar
CC Member
Visit my Photo Gallery
 
Join Date: Sep 2002
Location: Hickory, NC
Cobra Make & Engine: ERA 427SC w/427so, ERA GT #2002
Posts: 1,106
Default

Here's a closeup of the front pivot less shims on the back side. Rear pivot looks the same. I'll post an overall picture, too.

Guess what I'll do is loosen the pivot bolts, fit the shims in real tight, then secure the bolts. I'll have to saw off a short section of hex to fit the socket-head bolt and use a box-end wrench to loosen and tighten bolts. Next stop will be the alignment rack to see where the steering wheel, caster and toe ended up.
__________________
Tom

"If you can make black marks on a straight from the time you turn out of a corner until the braking point of the next turn, then you have enough HORSEPOWER." Mark Donohue
Reply With Quote
  #4 (permalink)  
Old 11-13-2006, 05:57 PM
speed220mph's Avatar
CC Member
Visit my Photo Gallery
 
Join Date: Sep 2002
Location: Hickory, NC
Cobra Make & Engine: ERA 427SC w/427so, ERA GT #2002
Posts: 1,106
Default

Ron: Here's another try with the pictures:



__________________
Tom

"If you can make black marks on a straight from the time you turn out of a corner until the braking point of the next turn, then you have enough HORSEPOWER." Mark Donohue
Reply With Quote
  #5 (permalink)  
Old 11-15-2006, 11:13 AM
Jim Holden's Avatar
CC Member
Visit my Photo Gallery
 
Join Date: Nov 1999
Location: White Plains,, NY
Cobra Make & Engine: ERA140, ERA 267, ERA GT2038, ERA FIA 2045, ERAGT2077 ERA2893000EXP
Posts: 1,117
Default

Two thoughts:

Post this over on the ERA area so that Bob Putnam is sure to see it or

Call Teddy up at ERA R&D 860-225-6344. It may take him a while to answer so keep trying. Teddy puts the GTs together in his sleep.

Jim
Reply With Quote
  #6 (permalink)  
Old 11-16-2006, 06:18 AM
speed220mph's Avatar
CC Member
Visit my Photo Gallery
 
Join Date: Sep 2002
Location: Hickory, NC
Cobra Make & Engine: ERA 427SC w/427so, ERA GT #2002
Posts: 1,106
Default

Thanks Jim. Got all the info I needed from Bob. Evidently the car was aligned by somone who didn't use ERA's recommendations on securing the shims, i.e., with cotter pins. They also left out the thrust washers, which allowed the bushing to be abraded, opening up thrust clearance.

As you say, Ted can put these cars together in his sleep. I just hate to bother him. But when I'm in a bind . . .

Thanks again.
__________________
Tom

"If you can make black marks on a straight from the time you turn out of a corner until the braking point of the next turn, then you have enough HORSEPOWER." Mark Donohue

Last edited by speed220mph; 11-17-2006 at 07:09 AM..
Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 01:03 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: