Club Cobra Keith Craft Racing  

Go Back   Club Cobra > Engine Building, Tuning, and Induction > Ignition

Keith Craft Racing
Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
Keith Craft Racing
Advertise at CC
Banner Ad Rates
Keith Craft Racing
MMG Superformance
MMG Superformance
MMG Superformance
December 2024
S M T W T F S
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31        

Kirkham Motorsports

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #1 (permalink)  
Old 11-13-2010, 09:01 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2009
Cobra Make, Engine:
Posts: 2
Not Ranked     
Default No spark, need help......

OK, I'm having a huge problem solving this no spark problem. But I'll not bore you with all the previous fault finding but say I have replaced the TFI, distributor is new, coil is new and wiring point to point checked, and a re-manufactured EEC IV installed.

So back to basics and check that the coil would spark off the car. With the connections below what do you think momentary connection of the black wire to battery negative would do?
Just for clarification the red lead is to the coil + and the black is switching the coil - to 0V.



I was expecting a nice fat spark but no? Tried the original coil, no spark and even checked with another new coil, still no spark?

What am I missing, this problem is a PITA

Could someone please replicate this set up in their garage and let me know what happens?

John
Reply With Quote
  #2 (permalink)  
Old 11-13-2010, 09:51 PM
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jul 2002
Cobra Make, Engine:
Posts: 15,712
Not Ranked     
Default

The basic wiring looks like it should work. Assuming... The positive wire resting on the top of the pos terminal of the battery is actually getting a good connection, it doesn't look like a good connection. Did you use a meter to verify 12 volts at the two coil terminals?

If so, then a sharp and sudden break of the negative connection at the battery terminal should result in spark.
Reply With Quote
  #3 (permalink)  
Old 11-13-2010, 11:40 PM
Rick Parker's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2001
Location: California, Ca
Cobra Make, Engine: NAF 289 Slabside Early Comp Car with 289 Webers and all the goodies. Cancelling the efforts of several Priuses
Posts: 6,592
Not Ranked     
Default

Doesn't the missing module step up the primary voltage, I believe so.
__________________
Rick

As you slide down the Banister of Life, may the splinters never be pointing the wrong way
Reply With Quote
  #4 (permalink)  
Old 11-14-2010, 06:54 AM
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jul 2002
Cobra Make, Engine:
Posts: 15,712
Not Ranked     
Default

If I recall the MSD module's step up in the neighborhood of 400 volts, so it's a good question Rick.

That would be: Does THIS coil require the high primary voltage in order to fire?
Reply With Quote
  #5 (permalink)  
Old 11-14-2010, 07:09 AM
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jul 2002
Cobra Make, Engine:
Posts: 15,712
Not Ranked     
Default

Uh oh, it just dawned on me that many of todays modern coils work fine with a module but will BURN UP if you use 12 volts direct to the primary circuit. Many of them REQUIRE a ballast resistor that drops the 12 volts to about 6 (7 or 8 maybe).

It's possible the coils that have been tested with the above wiring schematic are now toast.
Reply With Quote
  #6 (permalink)  
Old 11-14-2010, 12:09 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2009
Cobra Make, Engine:
Posts: 2
Not Ranked     
Default

Thanks guys but the coil wiring for the Mustang does not include a ballast resistor.
The circuit does have good connections, the photo is just to show the configuration.
No spark, engine not run, no complete project......running out of ideas...
Reply With Quote
  #7 (permalink)  
Old 11-14-2010, 12:38 PM
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jul 2002
Cobra Make, Engine:
Posts: 15,712
Not Ranked     
Default

Very few cars, these days DO include a ballast resistor. It's function is handled by an electronic type ignition control module. But what your doing is like an old school point and condensor type wiring, no electronics, just wired straight to the battery with the negative wire acting, as it were, "the points". A mechanical switch that makes or breaks the current, with a condensor that helps to limit arcing across the point contacts which would lead to burned and pitted contacts.

SOME coil's have an INTERNAL ballast resistor, some require an external one. Often, with todays modern coils designed to work with electronics, they do not have nor require an INTERNAL resistor. A resister can be purchased from any neighborhood parts store. They all serve the same basic function, reducing the voltage from 12 to 6 or 7 volts. It really doesn't matter what vehicle you have, if it came with points, it had a resistor OR (like GM) a resistor WIRE included in the wiring harness.

12 volts to a coil without a resistor will burn up the primary wiring inside the coil, you will not see the damage.
Reply With Quote
  #8 (permalink)  
Old 07-04-2011, 11:23 AM
Murky781's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2011
Location: Farmington, CT
Cobra Make, Engine: ERA 781, 69' 428CJ, PPG BLACK. ERA 3005 Arctic White 331 SBF
Posts: 280
Not Ranked     
Default

Adding to this thread because I have NO SPARK. 69' 428, MSD-6AL, replaced coil, voltage reg. ignition switch. Did the paper clip test on the MSD, it was good. Car turns over quickly, but will not fire. Screwdriver in coil wire doesn't spark. Dist. is turning, rotor looks good, not carbon trails in cap. Battery fully charged and grounds checked.
Car ran great, then was hard to start, (20 secs. cranking) turned it off, then 40 sec cranking. one last start of close to a minute cranking, got it home and it will not spark now. I'm open to help, dash is out and i have power to ign. switch with power on and cranking. Beautiful day and I'm stuck!!! thanks guys
It's an ERA if that makes any difference
__________________
We make 3 bad decisions a day. Choose them wisely.
Reply With Quote
  #9 (permalink)  
Old 07-04-2011, 11:59 AM
CC Member
Visit my Photo Gallery

 
Join Date: Aug 2009
Location: Alpine, TX
Cobra Make, Engine: #010 SC motorcars 428PI TKO600
Posts: 109
Not Ranked     
Default MSD pu coil

I had a msd pickup coil in the dist go bad and that is how it acted, paper clip test said box was okay, but the pickup coil in the dist failed, replaced it and it worked. For the record it started to act up several days earlier, would be very hard to start, had to crank and crank and finally it would start, then it left me stranded at the store, no spark, had to tow it home, took a week for me to find the problem. Hope that helps.
David
Reply With Quote
  #10 (permalink)  
Old 07-04-2011, 12:22 PM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 22,005
Not Ranked     
Default

Quote:
Originally Posted by Murky781 View Post
Adding to this thread because I have NO SPARK. 69' 428, MSD-6AL, replaced coil, voltage reg. ignition switch. Did the paper clip test on the MSD, it was good.
When you do this, what is the result? Do you get a spark to ground?

1. Make sure the ignition switch is in the “Off” position.
2. Remove the coil wire from the distributor cap and set the terminal approximately 1/2" from ground.
3. Disconnect the MSD magnetic pickup wires from the distributor.
4. Turn the ignition to the On position. Do not crank the engine.
5. With a small jumper wire, short the MSD’s Green and Violet magnetic pickup wires together several times. Each time you break this short, a spark should jump from the coil wire to ground.
Reply With Quote
  #11 (permalink)  
Old 07-04-2011, 12:58 PM
Murky781's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2011
Location: Farmington, CT
Cobra Make, Engine: ERA 781, 69' 428CJ, PPG BLACK. ERA 3005 Arctic White 331 SBF
Posts: 280
Not Ranked     
Default

To Dave... that's what went on with this. Haven't checked that yet..any easy way to do it? Patrick..I did that and I get a good spark to ground. I'm just lost as where to go. No spark from coil wire to ground by cranking.
thanks
__________________
We make 3 bad decisions a day. Choose them wisely.
Reply With Quote
  #12 (permalink)  
Old 07-04-2011, 01:01 PM
Rick Parker's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2001
Location: California, Ca
Cobra Make, Engine: NAF 289 Slabside Early Comp Car with 289 Webers and all the goodies. Cancelling the efforts of several Priuses
Posts: 6,592
Not Ranked     
Default

One other item to mention, doesn't the coil frame require a ground also?
__________________
Rick

As you slide down the Banister of Life, may the splinters never be pointing the wrong way
Reply With Quote
  #13 (permalink)  
Old 07-04-2011, 01:04 PM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 22,005
Not Ranked     
Default

Quote:
Originally Posted by Murky781 View Post
Patrick..I did that and I get a good spark to ground. I'm just lost as where to go. No spark from coil wire to ground by cranking.
thanks
The the next step is to keep everything exactly the same and plug the magnetic pickup back in and crank it. If you see no spark going to ground while cranking then it is the magnetic pickup.
Reply With Quote
  #14 (permalink)  
Old 07-04-2011, 01:15 PM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 22,005
Not Ranked     
Default

BTW, the gap between the reluctor wheel and the magnetic pickup should be about .028 to .030 of an inch. If it's really out of whack, that can keep it from sending the signal to trigger the spark.
Reply With Quote
  #15 (permalink)  
Old 07-04-2011, 01:35 PM
Murky781's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2011
Location: Farmington, CT
Cobra Make, Engine: ERA 781, 69' 428CJ, PPG BLACK. ERA 3005 Arctic White 331 SBF
Posts: 280
Not Ranked     
Default

Thank you Patrickt.. No spark after replug. I'm guessing the magnetic pickup is that little blue thingy under my rotor? Hard to get a feeler gauge in there, but it looks like nothings moved way out of whack. Now where does one get a mag. pickup? MSG? Frustrated, but appreciate the help.
__________________
We make 3 bad decisions a day. Choose them wisely.
Reply With Quote
  #16 (permalink)  
Old 07-04-2011, 01:36 PM
Rick Parker's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2001
Location: California, Ca
Cobra Make, Engine: NAF 289 Slabside Early Comp Car with 289 Webers and all the goodies. Cancelling the efforts of several Priuses
Posts: 6,592
Not Ranked     
Default

Magnetic pickup ..........replace it, you have an open circuit
__________________
Rick

As you slide down the Banister of Life, may the splinters never be pointing the wrong way
Reply With Quote
  #17 (permalink)  
Old 07-04-2011, 01:38 PM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 22,005
Not Ranked     
Default

Quote:
Originally Posted by Murky781 View Post
Thank you Patrickt.. No spark after replug. I'm guessing the magnetic pickup is that little blue thingy under my rotor? Hard to get a feeler gauge in there, but it looks like nothings moved way out of whack. Now where does one get a mag. pickup? MSG? Frustrated, but appreciate the help.
Here's a pic of it. Believe it or not, a lot of local auto parts stores will have them right there on the aisle. I know Pep Boys carries them around here.


Last edited by patrickt; 07-04-2011 at 01:44 PM..
Reply With Quote
  #18 (permalink)  
Old 07-04-2011, 01:48 PM
Murky781's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2011
Location: Farmington, CT
Cobra Make, Engine: ERA 781, 69' 428CJ, PPG BLACK. ERA 3005 Arctic White 331 SBF
Posts: 280
Not Ranked     
Default

Thank you guys. Love the help on here. Such a nice day and I'm stuck driving the truck. Love the car and my wife is pissed that we can't cruise today. Only 700 miles on it and still working out the bugs, but the driving learning curve is pretty steep, so I'm taking it slow anyway. I'll start reassembling the dash and steering so I might be ready tomorrow. Either that or pour a really big bourbon and say to heck with it!! Thanks sagain, and I'll let you know. Patrickt, I'll be seeing Peter P and the gang tomorrow morning anyway returning an ignigtion switch. I'll let them know you're in their corner all the time! Thanks
__________________
We make 3 bad decisions a day. Choose them wisely.
Reply With Quote
  #19 (permalink)  
Old 07-04-2011, 01:50 PM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 22,005
Not Ranked     
Default

Quote:
Originally Posted by Murky781 View Post
Patrickt, I'll be seeing Peter P and the gang tomorrow morning anyway returning an ignigtion switch. I'll let them know you're in their corner all the time! Thanks
My offer stands to pay them if they will just let me come and work there for them.
Reply With Quote
  #20 (permalink)  
Old 07-04-2011, 02:05 PM
Rick Parker's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2001
Location: California, Ca
Cobra Make, Engine: NAF 289 Slabside Early Comp Car with 289 Webers and all the goodies. Cancelling the efforts of several Priuses
Posts: 6,592
Not Ranked     
Default

When you are installing it, if you get the MSD OEM unit, they caution you as to the correct magnet orientation. Get it wrong and you will open another can of worms. Do NOT crack it either. Be careful of the wires being connected properly, it it easy to do it wrong .
__________________
Rick

As you slide down the Banister of Life, may the splinters never be pointing the wrong way
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 04:59 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink