Welcome to Club Cobra! The World's largest
non biased Shelby Cobra related site!
- » Representation from nearly all
Cobra/Daytona/GT40 manufacturers
- » Help from all over the world for your
questions
- » Build logs for you and all members
- » Blogs
- » Image Gallery
- » Many thousands of members and nearly 1
million posts!
YES! I want to register an account for free right now!
p.s.: For registered members this ad will NOT show
 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
|
November 2024
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
|
|
|
1 |
2 |
| 3 |
4 |
5 |
6 |
7 |
8 |
9 |
| 10 |
11 |
12 |
13 |
14 |
15 |
16 |
| 17 |
18 |
19 |
20 |
21 |
22 |
23 |
| 24 |
25 |
26 |
27 |
28 |
29 |
30 |
|
|
CC Advertisers
|
|
 27Likes
08-26-2014, 06:02 AM
|
 |
CC Member
|
|
|
Join Date: May 2010
Location: Birmingham,
AL
Cobra Make, Engine: Kirkham 289 FIA, 363 Stroker
Posts: 751
|
|
Not Ranked
The Kirkham's are making an undercar exhaust system with a side exit in front of the rear wheels. After speaking with David about the headers and the heat shields that are necessary, it was definitely the best option to go ahead and have them make the system.
|
-
Advertising
08-27-2014, 10:05 AM
|
|
CC Member
|
|
|
Join Date: May 2010
Location: Birmingham,
AL
Cobra Make, Engine: Kirkham 289 FIA, 363 Stroker
Posts: 751
|
|
Not Ranked
Flywheel, pressure plate, clutch, bellhousing, hydraulic clutch slave, intake, and reverse rotation water pump are now installed.
Unfortunately, concept 1 sent me the wrong pulley system, so it all has to be removed and returned. They are sending me the correct system, but this one will be polished instead of black anodized.
Checking the bellhousing alignment. Everything checked out ok.
Aluminum TKO bellhousing, clutch fork, and clutch slave kit from Modern Driveline.
Their clutch slave kit was very easy to install.
Wrong pulley system
 |
08-27-2014, 05:57 PM
|
 |
CC Member
|
|
|
Join Date: Jun 2014
Location: Dallas,
TX
Cobra Make, Engine: ERA #812 427/482 FE
Posts: 495
|
|
Not Ranked
Aluminum bell housing
Are you not worried about the aluminum bell housing failing to contain debris if the clutch blows? I would be...
__________________
Chris
|
08-27-2014, 07:52 PM
|
|
CC Member
|
|
|
Join Date: May 2010
Location: Birmingham,
AL
Cobra Make, Engine: Kirkham 289 FIA, 363 Stroker
Posts: 751
|
|
Not Ranked
Quote:
Originally Posted by RockBit
Are you not worried about the aluminum bell housing failing to contain debris if the clutch blows? I would be...
|
Not one bit. How many production sports cars came with and still come with aluminum bell housings? I've built a lot of cars and I've never had a clutch blow apart. Besides, most of the steel bell housings are so poorly machined that they do not fit correctly and require offset dowels. Not to mention, they weigh and cost entirely too much. |
08-28-2014, 04:43 PM
|
 |
CC Member
|
|
|
Join Date: May 2006
Location: Portland,
OR
Cobra Make, Engine: ERA FIA, 1964 289->Webers
Posts: 3,689
|
|
Not Ranked
That's is a nice slave kit. What are the chances of a clutch exploding & the circumstances in which this has happened using modern components? I have picked up a cast iron bellhousing since finishing my car. I wish to eventually install it. I don't race, though. So the urgency to do so has taken a back shelf.
__________________
ERA FIA 2088
|
08-29-2014, 04:31 PM
|
|
CC Member
|
|
|
Join Date: May 2010
Location: Birmingham,
AL
Cobra Make, Engine: Kirkham 289 FIA, 363 Stroker
Posts: 751
|
|
Not Ranked
Well, it is now for sale if you want it.  I pulled the tremec from another build and forgot that the kirkhams need a short input shaft installed on the tremec and a different bell housing, so things are off by about 1/2". The braided hydraulic hose the kirkhams installed will not reach the slave i installed, so i am just going to switch to one of their arms and a pull style slave instead of a push.
So, the bellhousing, slave, and clutch fork are now for sale. |
09-25-2014, 06:32 PM
|
|
CC Member
|
|
|
Join Date: May 2010
Location: Birmingham,
AL
Cobra Make, Engine: Kirkham 289 FIA, 363 Stroker
Posts: 751
|
|
Not Ranked
Well, I did not make the deadline for my wedding, but that is ok. Our venue was in the middle of nowhere Georgia, so it would have been a pain to trailer the car there anyway.
New concept 1 pulley system installed. I have to say that concept 1 really went to great lengths to correct their mistake and even offered to drive the correct pulley system to me on a Saturday so I would have it on time. Nice people!
The tube on the Kirkham tank interferes with the connection of the upper radiator hose, so I am going to have my fabricator cut a wedge at the top, angle it up slightly, then TIG it from the inside.
 |
09-25-2014, 07:46 PM
|
 |
CC Member
|
|
|
Join Date: Jun 2010
Cobra Make, Engine: Viking Blue "64" 289 FIA comp car by Superformance #0002, Keith Craft - 331 (460HP), Jim Inglese - 48IDA Weber carbs, BW T10 4spd.
Posts: 430
|
|
Not Ranked
Last edited by LightNFast; 09-25-2014 at 07:49 PM..
|
09-26-2014, 06:11 AM
|
|
CC Member
|
|
|
Join Date: May 2010
Location: Birmingham,
AL
Cobra Make, Engine: Kirkham 289 FIA, 363 Stroker
Posts: 751
|
|
Not Ranked
Thanks for the links and not a bad idea, but I'm afraid it is too tight for a reducer to work.
|
10-01-2014, 04:07 PM
|
|
CC Member
|
|
|
Join Date: May 2010
Location: Birmingham,
AL
Cobra Make, Engine: Kirkham 289 FIA, 363 Stroker
Posts: 751
|
|
Not Ranked
Well, I had the car ready to run today, but I have no fire in the hole! Once again, there is an issue with a magnetic pickup on an MSD distributor. I'm ordering a new pickup tonight and hopefully it will be here by Friday. Everything else tests out fine...msd box, fuel pressure, initial carb settings, etc. Now I remember why i swore off MSD products after the last build!
CORRECTION: I only had power to the digital 6 box with the key in the ON position, but not in the crank position. Correct wire run to the box and now all is well.
Last edited by RestoCreations; 10-02-2014 at 01:35 PM..
|
10-02-2014, 01:37 PM
|
|
CC Member
|
|
|
Join Date: May 2010
Location: Birmingham,
AL
Cobra Make, Engine: Kirkham 289 FIA, 363 Stroker
Posts: 751
|
|
Not Ranked
She's alive! It sounds pretty terrible due to the leaky headers(no gaskets yet), but none the less, it is up and running, which is a good feeling.
Posted better video below.
Last edited by RestoCreations; 10-02-2014 at 02:38 PM..
|
10-02-2014, 02:37 PM
|
|
CC Member
|
|
|
Join Date: May 2010
Location: Birmingham,
AL
Cobra Make, Engine: Kirkham 289 FIA, 363 Stroker
Posts: 751
|
|
Not Ranked
Here is a better video. I secured the headers, but they still have leaks since I don't have the correct gaskets yet.
[ame="https://www.youtube.com/watch?v=8jn8CK-uF1g&list=UUSktJKxQzFvTs3EjFl1v-uA"]https://www.youtube.com/watch?v=8jn8CK-uF1g&list=UUSktJKxQzFvTs3EjFl1v-uA[/ame]
|
10-02-2014, 03:04 PM
|
|
CC Member
|
|
|
Join Date: May 2006
Location: Portland,
OR
Cobra Make, Engine: ERA FIA, 1964 289->Webers
Posts: 3,689
|
|
Not Ranked
That's always a big step & a damn good feeling. Congratulations!
__________________
ERA FIA 2088
|
10-02-2014, 06:47 PM
|
 |
Senior Club Cobra Member
|
|
|
Join Date: Mar 2005
Location: Manchester,
NH
Cobra Make, Engine: AK1085 (302 Street), HTM111 (427 Comp), CSX2375R (289 Comp) and COB5999 (427 S/C)
Posts: 18,997
|
|
Not Ranked
Great feeling when it runs...........
|
10-03-2014, 07:37 AM
|
|
CC Member
|
|
|
Join Date: May 2010
Location: Birmingham,
AL
Cobra Make, Engine: Kirkham 289 FIA, 363 Stroker
Posts: 751
|
|
Not Ranked
I have to say, I feel like I am cheating. I think I only have around 25 hours total in the car so far.
|
11-25-2014, 06:46 PM
|
|
CC Member
|
|
|
Join Date: May 2010
Location: Birmingham,
AL
Cobra Make, Engine: Kirkham 289 FIA, 363 Stroker
Posts: 751
|
|
Not Ranked
Well, one issue is resolved, but there are major issues with the exhaust and I am still waiting on a VIN tag. Not sure why my car did not come with one attached, but it did not.
I had my fabricator make a spacer for the coolant tank so that it would clear the alternator.
 |
12-12-2014, 11:45 PM
|
 |
CC Member
|
|
|
Join Date: Dec 2012
Cobra Make, Engine:
Posts: 4
|
|
Not Ranked
Maybe I missed it, did you say you're keeping the body in raw aluminum?
What tires are you planning to use?
Nice build.
|
12-17-2014, 07:49 AM
|
|
CC Member
|
|
|
Join Date: May 2010
Location: Birmingham,
AL
Cobra Make, Engine: Kirkham 289 FIA, 363 Stroker
Posts: 751
|
|
Not Ranked
Quote:
Originally Posted by 2112
Maybe I missed it, did you say you're keeping the body in raw aluminum?
What tires are you planning to use?
Nice build.
|
That's the plan currently, but I can't find anybody that is willing to Tig weld the bad areas on the hood, so I might not have a choice but to paint the car. My dream was to have a brushed aluminum body, but i guess you can't always get what you want.
I'm keeping the crappy tires that came on the car for now. The car was supposed to come with bf goodrich, but it has futura tires, which i have never heard of. Apparently it is getting harder to find the right size for 15" rims, so that is why the futura tires were supplemented.
Last edited by RestoCreations; 12-17-2014 at 08:00 AM..
|
12-17-2014, 07:58 AM
|
|
CC Member
|
|
|
Join Date: May 2010
Location: Birmingham,
AL
Cobra Make, Engine: Kirkham 289 FIA, 363 Stroker
Posts: 751
|
|
Not Ranked
The header supplies arrived at my fabricators shop the other day. I will post updates as he progresses. Note the notches in the flanges for clearance of the plug wire boots.
Again, the kirkham headers would not work on my car due to the high port heads that came with the Ford Racing 363 stroker...just a note for those that might make the same mistake. I have the Kirkham headers listed in the for sale section if anyone is interested.
[IMG]  [/IMG] |
12-17-2014, 09:01 AM
|
 |
CC Member
|
|
|
Join Date: Feb 2001
Location: BRADENTON,
FL
Cobra Make, Engine: KIRKHAM 427 S/C, SHELBY 427 ALUM. STROKER
Posts: 1,396
|
|
Not Ranked
Resto: Did you order your car with file or brushed finish ? I find it hard to believe Kirkham would send out something not right. Have you contacted them about the hood?
I bought a complete hood some years ago that was made for another car. It didn't fit properly ( too narrow). Had a local welder put 2 beads down one side and 3 on the other. After filing and sanding ,it fit fine and you couldn't tell it had been done. What exactly is the problem with your hood ? You wanted brushed finish, don't give up so easily !
Ted
__________________
"When Injustice becomes Law,
Rebellion becomes Duty." T. Jefferson
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 11:59 PM.
|
|
Linear Mode
