 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
|
1 |
2 |
3 |
4 |
| 5 |
6 |
7 |
8 |
9 |
10 |
11 |
| 12 |
13 |
14 |
15 |
16 |
17 |
18 |
| 19 |
20 |
21 |
22 |
23 |
24 |
25 |
| 26 |
27 |
28 |
29 |
30 |
31 |
|
|
|
CC Advertisers
|
|
03-22-2008, 11:46 AM
|
 |
Senior Club Cobra Member
|
|
|
Join Date: Mar 2006
Location: Jacksonville,
FL
Cobra Make, Engine: Hi-Tech
Posts: 480
|
|
Not Ranked
Someone just tried that.  |
03-22-2008, 11:54 AM
|
 |
Half-Ass Member
|
|
|
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 22,011
|
|
Not Ranked
Quote:
Originally Posted by hi-tech cobra
Someone just tried that. |
Computerworks & Jamo on a bender, perhaps?  |
03-22-2008, 12:18 PM
|
|
Senior Club Cobra Member
|
|
|
Join Date: Jul 2003
Location: Santa Fe,
NM
Cobra Make, Engine: Cardiac, 428 FE
Posts: 301
|
|
Not Ranked
Hi-Tech,
I have some info for you if you're still looking for original Ford pulley's. I sent an email to you a bit ago. Just found some yesterday and there's more parts there for an FE as well.
Look at your email and we can go from there.
Paul
|
03-23-2008, 08:07 AM
|
|
CC Member
|
|
|
Join Date: Apr 2001
Location: Abe Lincolns Birthplace,
Ky
Cobra Make, Engine: CSX4761, KCR Shelby Alloy 496,760hp
Posts: 867
|
|
Not Ranked
You should be able to use any single groove FE pulleys including 352,360 and 390 truck motors. Salvage yards and recycling places usually have complete junk motors around.I think some of the cobra parts places like cobra restorers sell them new .I wouldnt be suprised if they aren't still serviced by ford.
I used a set of march pulleys on my motor which look like stock after I painted them to hide the ugliness of billet,lol.
good luck,Tim
__________________
Tk
"this whole Adult thing just isnt working for me "
|
04-15-2008, 12:43 PM
|
|
Senior Club Cobra Member
|
|
|
Join Date: Mar 2006
Location: Jacksonville,
FL
Cobra Make, Engine: Hi-Tech
Posts: 480
|
|
Not Ranked
I got the engine in and it has a crank pulley, see pic. So all I need is the water pump pulley. Does it look like a regular FE stamped steel pulley will work?
Better pics in my gallery.
|
04-15-2008, 12:49 PM
|
|
Half-Ass Member
|
|
|
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 22,011
|
|
Not Ranked
Quote:
Originally Posted by hi-tech cobra
I got the engine in and it has a crank pulley, see pic. So all I need is the water pump pulley. Does it look like a regular FE stamped steel pulley will work?
Better pics in my gallery.
|
You know I think it might. But you won't know until you bolt it on and lay a straight edge on them. |
04-15-2008, 12:52 PM
|
|
CC Member
|
|
|
Join Date: Apr 2001
Location: Abe Lincolns Birthplace,
Ky
Cobra Make, Engine: CSX4761, KCR Shelby Alloy 496,760hp
Posts: 867
|
|
Not Ranked
I think a stock pulley will work but it is hard to tell by the pic. If you like I can get a measurement from something for you tonite . I see the stock pulleys on ebay fairly regular. T
__________________
Tk
"this whole Adult thing just isnt working for me "
|
04-15-2008, 07:30 PM
|
|
CC Member
|
|
|
Join Date: Apr 2001
Location: Abe Lincolns Birthplace,
Ky
Cobra Make, Engine: CSX4761, KCR Shelby Alloy 496,760hp
Posts: 867
|
|
Not Ranked
I have an eldebrock water pump and I believe the same ati dampener that you do.I am using march pulleys with a stock ford fe alternator and mounting setup .My top pulley belt groove is 5 and 5/8th inches to the block measured from the machined flat just over the passenger side water pump port to the center of the pulley v groove.
The lower pulley measures 3 and 3/8's inches from the center of the v groove to the flat between the mounting bolts on the stock timing pointer.
I also measured a different engine on the flloor that has the same water pump but all stock steel pulleys,all measurements are identical.
I hope this helps,I'll be glad to take pics if you need them. ,Tim
__________________
Tk
"this whole Adult thing just isnt working for me "
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 07:59 PM.
Links monetized by VigLink
|
Linear Mode
