Club Cobra GasN Exhaust  

Go Back   Club Cobra > Engine Building, Tuning, and Induction > Small Block Talk

Keith Craft Racing
Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
MMG Superformance
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
MMG Superformance
Keith Craft Racing
December 2024
S M T W T F S
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31        

Kirkham Motorsports

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #1 (permalink)  
Old 12-11-2009, 02:50 AM
ALF's Avatar
ALF ALF is offline
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2003
Location: Switzerland, CH
Cobra Make, Engine:
Posts: 536
Not Ranked     
Question oil puke tank line routing

Hello

I was able to organize a oil puke tank to mount on my 289 USRRC Cobra. Now I'm curios about the line routing.



Where do I need to connect it and how?
- Valve covers (I can see on the picture)
- Transmission (where and how?)
- Oil pan (where and how?)
- ??

Where should it go and how did you connect it?

Please post some picture, which help to better understand it!


Thanks
ALF
Reply With Quote
  #2 (permalink)  
Old 12-11-2009, 05:09 AM
mickmate's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Sep 2000
Location: Holderness, NH, US of A, NH
Cobra Make, Engine: CSX 4772 old iron FE
Posts: 5,499
Not Ranked     
Default

Hey Alf, 427's use a hose to the intake manifold, a smaller one to the trans cover, a draft tube to the tunnel and a lower drain tube to the pan. It looks like the 289 picture has the breather to the valve covers and one underneath it heading to the pan? The other side looks like a draft tube up high maybe a tranny one below it?
__________________
mickmate
http://www.actoncustom.com/
Reply With Quote
  #3 (permalink)  
Old 12-11-2009, 07:24 AM
*13*'s Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2006
Location: Portland, OR
Cobra Make, Engine: ERA FIA, 1964 289->Webers
Posts: 3,689
Not Ranked     
Default

I looked to see if I had a better picture of that car, I don't. I'd agree that the bottom line looks like it may be heading to the pan? Could be to the intake but that might be a squeeze with the linkage. I've been hoping to see that car again to see some more of the engine compartment details. If I do I'll get some pictures
__________________
ERA FIA 2088
Reply With Quote
  #4 (permalink)  
Old 01-04-2010, 04:52 AM
ALF's Avatar
ALF ALF is offline
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2003
Location: Switzerland, CH
Cobra Make, Engine:
Posts: 536
Not Ranked     
Exclamation

Hello

Many thanks for your feedback.
I've now the tank in my hands and I'm still trying to find the correct way to connect it!




As I use a 289 T-Pan and a Weber 48IDA intake I'm not sure where and how to connect there.
i.E.. there is no breather on the intake and I don't remember one on the T-Pan.

Appreciate any help (best with picture or drawings). This helps to reduce misunderstandings!
Reply With Quote
  #5 (permalink)  
Old 01-04-2010, 05:04 AM
mickmate's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Sep 2000
Location: Holderness, NH, US of A, NH
Cobra Make, Engine: CSX 4772 old iron FE
Posts: 5,499
Not Ranked     
Default

On the 427 A is a draft tube into tunnel, B is back of intake manifold, C is oil pan, D is trans cover, E gets plugged. On original 289 pans it looks like the dipstick is in the motor and the fitting in the side is for a hose barb for the puke tank drain tube http://aviaid.com/shopsite_sc/store/...s_sbf-ss2.html
__________________
mickmate
http://www.actoncustom.com/
Reply With Quote
  #6 (permalink)  
Old 01-19-2010, 11:39 AM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2008
Location: Near Chichester, Sussex by the sea......, UK
Cobra Make, Engine: Crendon 427 S/C 428 FE+toploader
Posts: 668
Not Ranked     
Default Puke tank connections on a 427

I dont think these puke tanks connect to the valve covers on a 427?

So can anyone list the correct connections? (just got one today )

Maybe lost in translation, and at risk of sounding like a complete arse, what is a 'draft tube'? - just a tube for carrying oil vapor?
also, 'trans cover' - is this a plate on the top of a toploader gearbox?

thanks, Kevin
__________________
Crendon 427, in the making
http://crendonreplicas.com/
Reply With Quote
  #7 (permalink)  
Old 01-19-2010, 11:46 AM
Gunner's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2009
Location: Sacramento, CA
Cobra Make, Engine: ERA 707, 446ci FE
Posts: 1,115
Not Ranked     
Default

Google up "road draft tube" - it's a metal tube, usually with a 45* slant tip, that points down towards the road and ends about where the bottom of the oil pan is. All cars used to have these. The idea was that air rushing past the slant tip would create a slight vacuum and pull fumes out of the crankcase... where, of course, they would just dissipate into the atmosphere, never harming nobody.

This is also the reason all roads used to have a black oily line down the center of each lane. Since this wasn't acceptable on race tracks, the puke tank was used to catch (in theory) the liquid oil.

Also: AFAIK, no engines had vents or tubes or breathers on the valve covers until the advent of smog controls in the early 1960s, and performance engines lagged behind road engines. I'd be surprised if any original Cobra engine had them.
__________________

= Si Opus Quadratum vis, angulos praecidere noli. =
Reply With Quote
  #8 (permalink)  
Old 01-19-2010, 12:04 PM
mickmate's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Sep 2000
Location: Holderness, NH, US of A, NH
Cobra Make, Engine: CSX 4772 old iron FE
Posts: 5,499
Not Ranked     
Default

Quote:
So can anyone list the correct connections?
Already have.
__________________
mickmate
http://www.actoncustom.com/
Reply With Quote
  #9 (permalink)  
Old 01-19-2010, 12:30 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2008
Location: Near Chichester, Sussex by the sea......, UK
Cobra Make, Engine: Crendon 427 S/C 428 FE+toploader
Posts: 668
Not Ranked     
Default

Quote:
Originally Posted by mickmate View Post
On the 427 A is a draft tube into tunnel, B is back of intake manifold, C is oil pan, D is trans cover, E gets plugged. On original 289 pans it looks like the dipstick is in the motor and the fitting in the side is for a hose barb for the puke tank drain tube http://aviaid.com/shopsite_sc/store/...s_sbf-ss2.html

er yep, doh! ....not paying attention properly.
still got some questions, i think due to translation probs.....hope you can help...

A is a draft tube into tunnel
- so I run a metal pipe into the tunnel and drop it down at an angle so it drips oil on the road? sure i got this wrong??!!

B is back of intake manifold
OK got that one!

C is oil pan,
D is trans cover,

how do these 2 work- doesnt one go on the differential? or is that the trans cover - thought trans was a US term for gearbox?

E gets plugged. OK got it.

Do you ever need to empty an oil puke tank?

cheers, kevin
__________________
Crendon 427, in the making
http://crendonreplicas.com/

Last edited by KevinW; 01-19-2010 at 12:33 PM..
Reply With Quote
  #10 (permalink)  
Old 01-19-2010, 12:41 PM
mickmate's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Sep 2000
Location: Holderness, NH, US of A, NH
Cobra Make, Engine: CSX 4772 old iron FE
Posts: 5,499
Not Ranked     
Default

A-Draft tube allows vapors (not oil) to escape down into the tunnel. That's why it comes off a top one.
B-Back of manifold, if you need a plate check my site.
C-sump to the Pom
D-trans is the gearbox, I put a little tube welded in to top of trans cover, you could drill and tap for a small hose barb also.
The tube that goes to the oil pan comes off the bottom of the tank draining any yuckies into the pan. That's why we change oil regularly as it also allows condensation into the pan.
__________________
mickmate
http://www.actoncustom.com/

Last edited by mickmate; 03-29-2010 at 12:22 PM.. Reason: spilling mistak
Reply With Quote
  #11 (permalink)  
Old 01-19-2010, 12:47 PM
Gunner's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2009
Location: Sacramento, CA
Cobra Make, Engine: ERA 707, 446ci FE
Posts: 1,115
Not Ranked     
Default

Quote:
Originally Posted by mickmate View Post
B-Back of manifold, if you need a plate check my site.
I thought only the FEs had a space for the breather plate? SB manifolds have a fitting or need one drilled and tapped. My 289 Performer RPM uses the brass vacuum block for the crankcase vent.
__________________

= Si Opus Quadratum vis, angulos praecidere noli. =
Reply With Quote
  #12 (permalink)  
Old 01-19-2010, 02:41 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2008
Location: Near Chichester, Sussex by the sea......, UK
Cobra Make, Engine: Crendon 427 S/C 428 FE+toploader
Posts: 668
Not Ranked     
Default

thanks Mick.
Kevin
__________________
Crendon 427, in the making
http://crendonreplicas.com/
Reply With Quote
  #13 (permalink)  
Old 03-29-2010, 11:02 AM
snakehunter's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2010
Location: Cincinnati, Ohio, OH
Cobra Make, Engine: CSX4158, alloy body. The Watersnake!
Posts: 98
Not Ranked     
Default

So the puke tank is also the oil fill as well? And has anyone adapted a PCV to this setup? I've seen some where there's just a hole drilled in the valve cover with a rubber grommet.
Reply With Quote
  #14 (permalink)  
Old 03-29-2010, 12:31 PM
mickmate's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Sep 2000
Location: Holderness, NH, US of A, NH
Cobra Make, Engine: CSX 4772 old iron FE
Posts: 5,499
Not Ranked     
Default

On the originals the oil fill was a tube through the front right of the intake manifold.
The puke tank collected vapors till they condensed and filled enough to run down into the oil pan. That's why the different levels of tube from the puke tank (draft from top).
It's also the reason for the smooth valve covers........
__________________
mickmate
http://www.actoncustom.com/

Last edited by mickmate; 03-29-2010 at 12:36 PM..
Reply With Quote
  #15 (permalink)  
Old 03-29-2010, 01:27 PM
dcdoug's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2009
Location: Bethesda, MD
Cobra Make, Engine: CSX 6022, navy blue, period correct 427 SO
Posts: 2,154
Not Ranked     
Default

I find filling it up through this tube is a PITA by the way. With that baffle in the tube, it makes filling it up SLOW. Go too fast and it gets MESSY.
__________________
“There are only three sports: bullfighting, motor racing, and mountaineering; all the rest are merely games.”

www.partskeeper.com
(Less time searching, more time wrenching & driving)
Reply With Quote
  #16 (permalink)  
Old 03-29-2010, 01:36 PM
dcdoug's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2009
Location: Bethesda, MD
Cobra Make, Engine: CSX 6022, navy blue, period correct 427 SO
Posts: 2,154
Not Ranked     
Default

Mickmate - can you post a pick of the oil puke tank installed on a Cobra with an FE?
__________________
“There are only three sports: bullfighting, motor racing, and mountaineering; all the rest are merely games.”

www.partskeeper.com
(Less time searching, more time wrenching & driving)
Reply With Quote
  #17 (permalink)  
Old 03-29-2010, 01:38 PM
dcdoug's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2009
Location: Bethesda, MD
Cobra Make, Engine: CSX 6022, navy blue, period correct 427 SO
Posts: 2,154
Not Ranked     
Default

Quote:
Originally Posted by mickmate View Post

D-trans is the gearbox, I put a little tube welded in to top of trans cover, you could drill and tap for a small hose barb also.
What's the purpose of this connection? Intuitively it would seem like you just need the puke hose from the back of the manifold and then two tubes going out, one for vapors and one for oil back to the pan. So what's the other one for?

Doug
__________________
“There are only three sports: bullfighting, motor racing, and mountaineering; all the rest are merely games.”

www.partskeeper.com
(Less time searching, more time wrenching & driving)
Reply With Quote
  #18 (permalink)  
Old 03-29-2010, 02:51 PM
dcdoug's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2009
Location: Bethesda, MD
Cobra Make, Engine: CSX 6022, navy blue, period correct 427 SO
Posts: 2,154
Not Ranked     
Default

I have a Canton pan to which I would need to add a fitting for the puke tank drain back hose. Where on the pan was the original location? Anyone have a pic? What would be the right size fitting to add? I am actually going to change my oil pan to a road race pan, so now is a good time for me to at least add the fitting and a plug so I can add an oil puke tank later.
__________________
“There are only three sports: bullfighting, motor racing, and mountaineering; all the rest are merely games.”

www.partskeeper.com
(Less time searching, more time wrenching & driving)
Reply With Quote
  #19 (permalink)  
Old 03-29-2010, 02:52 PM
mickmate's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Sep 2000
Location: Holderness, NH, US of A, NH
Cobra Make, Engine: CSX 4772 old iron FE
Posts: 5,499
Not Ranked     
Default

It's the breather tube for the trans and the rear end I believe. There's a bump with a vent hole for street cars, comp cars are hooked to the puke tank for the vapors.


I'll post pictures of the 427 one hooked up in the BB forum.
__________________
mickmate
http://www.actoncustom.com/
Reply With Quote
  #20 (permalink)  
Old 03-29-2010, 02:52 PM
DougD's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2000
Location: Des Moines, IA
Cobra Make, Engine: Sold my beloved Shelby CSX 4068, Gessford 427 Ford
Posts: 756
Not Ranked     
Default

Quote:
Originally Posted by dcdoug View Post
What's the purpose of this connection? Intuitively it would seem like you just need the puke hose from the back of the manifold and then two tubes going out, one for vapors and one for oil back to the pan. So what's the other one for?

Doug
It's a vent for the gearbox. The originals had a hose running from the differential to a "T" on the gearbox, and then on up to the puke tank.

Opinions vary as to whether it's a good idea to connect all 3 together. I omitted the line from the differential to gearbox, but I did connect the gearbox to the puke tank.
__________________
CSX4068, '69 Bronco, '70 BOSS 302, '87 Mustang GT, '08 Roush Trak Pak
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 07:04 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink