Club Cobra Gas - N Exhaust  

Go Back   Club Cobra > Engine Building, Tuning, and Induction > Small Block Talk
Rotating Assembly Clearance Rotating Assembly Clearance
Portal Register FAQ Community For Sale Gallery Calendar Today's Posts

Keith Craft Racing
Nevada Classics
Keith Craft Racing
Main Menu
Portal
Forums

Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
MMG Superformance
Advertise at CC
Banner Ad Rates
MMG Superformance
Keith Craft Racing
MMG Superformance
Keith Craft Racing
November 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30

Kirkham Motorsports

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #1 (permalink)  
Old 08-12-2005, 02:09 PM
onefastmustang's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Location: Fairfield, ca
Cobra Make, Engine: CRII with a Stroked Windsor
Posts: 976
Not Ranked     
Default Rotating Assembly Clearance
Can anyone tell me whats an acceptable clearane from the crankshaft counterweight to the block. I am doing a test fit to see if everything clears.


Thanks

Mike
Reply With Quote
  #2 (permalink)  
Old 08-12-2005, 07:27 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2001
Location: Louisville, KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,415
Send a message via AIM to blykins
Not Ranked     
Default
When clearancing the block for a stroker crank, I was always told to leave .060" between the block and the rod bolts to allow for any expansion......I would say the same applies here.
__________________
Lykins Motorsports, LLC
Custom SBF/Cleveland/FE/385 Series Engines
Street, Road Race, Drag Race, Pulling Truck
www.lykinsmotorsports.com
www.customfordcams.com
brent@lykinsmotorsports.com
Reply With Quote
  #3 (permalink)  
Old 08-12-2005, 08:12 PM
onefastmustang's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Location: Fairfield, ca
Cobra Make, Engine: CRII with a Stroked Windsor
Posts: 976
Not Ranked     
Default
Thanks.. I measure .125" so I should be good to go..
Reply With Quote
  #4 (permalink)  
Old 08-13-2005, 04:37 PM
CC Member
Visit my Photo Gallery

 
Join Date: Aug 2005
Location: ft worth, tx
Cobra Make, Engine:
Posts: 12
Not Ranked     
Default
.060 is correct....alum rods go .100 for added security
Reply With Quote
Reply

« Previous Thread | Next Thread »

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


All times are GMT -7. The time now is 03:45 PM.

Contact Us - Club Cobra Home - Archive - Top

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink