Club Cobra Gas - N Exhaust  

Go Back   Club Cobra > Engine Building, Tuning, and Induction > Small Block Talk

MMG Superformance
Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
Advertise at CC
Banner Ad Rates
Keith Craft Racing
Keith Craft Racing
MMG Superformance
MMG Superformance
December 2024
S M T W T F S
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31        

Kirkham Motorsports

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #1 (permalink)  
Old 11-10-2008, 10:02 AM
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2005
Location: Milford, CT
Cobra Make, Engine: ERA 289FIA, 302 from Engine Factory
Posts: 11
Not Ranked     
Default Edelbrock 1806

Guys, I have the 1806 on an Edelbrock maifold on a '69 302 all built by the Engine Factory in New Jersey. The motor has been in my ERA FIA for 3 years. I've noticed lately that when starting from a complete stop, the motor hesitates & sputters a bit before taking off smoothly. Someone mentioned accelerator pump, I'd like to get your thoughts.......bad news, I'm not a mechanic, but I am handy and would like to learn.......thoughts???

Best,
Blake
Reply With Quote
  #2 (permalink)  
Old 11-10-2008, 12:33 PM
CC Member
Visit my Photo Gallery

 
Join Date: Aug 2007
Location: Carlsbad, Ca
Cobra Make, Engine: SPF 2932 with 438 Lykins Motorsports engine. Previous owner of FFR 5452.
Posts: 2,616
Not Ranked     
Default

Probably a simple adjustment.

Try richening up the idle adjustment screws, (both of them) about an eighth of a turn. (Counterclockwise)

Assuming the timing is set correctly.

Let us know if this doesn't work. Lots of other things can be done, but they become more complicated.

Last edited by jhv48; 11-10-2008 at 12:40 PM..
Reply With Quote
  #3 (permalink)  
Old 11-26-2008, 02:00 AM
PANAVIA's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2008
Location: San Jose CA, CA
Cobra Make, Engine: SPF_R_/BRG/FRBoss302/327CI/FordEFI/Under_Car_Exh/
Posts: 2,523
Not Ranked     
Default

possibly sounds like timing has shifted say from 10 BTDC to 6 BTDC and you are running on less than optimal base timing.

You may want to check your spark plugs and see if you can tell anything there --maybe you are running too much base fuel.
__________________
Steve SPF 2734 MK3 / Brock Coupe #54- panavia.com
Reply With Quote
  #4 (permalink)  
Old 11-26-2008, 08:16 AM
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2006
Location: Darnestown, MD
Cobra Make, Engine: ERA 289FIA, 289 stroked to 331, 392 HP
Posts: 478
Not Ranked     
Default

I don't know much about Edelbrock carbs, but when my old Holleys and Rochesters did that it was usually a problem with the accelerator pump seal.
Reply With Quote
  #5 (permalink)  
Old 11-26-2008, 09:24 PM
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2003
Location: PVE, CA
Cobra Make, Engine: ERA 289 FIA #2027, 65' 289" PS wheels
Posts: 345
Not Ranked     
Default I'm with Warren

In my distant past there was a Rochester 2-bbl on a 389" Pontiac...pretty much the same basic design...when the accelerator pump starts to leak the pump shot is too weak...a very easy rebuild as I remember it, the accelerator pump is a vertical plunger, if it has worn out, put in a new one and squirt the rest of the carb clean with cleaner a few times with an aerosol can of Gum-Out or whatever carb cleaner...try not to get it sprayed in your eyes...

Just be careful, get a toothbrush..clean the dirt off the outside of the carb before you take it apart...keep things clean...paper towels, clean dishes and pie tins for screws, etc...if you don't have compressed air use the carb cleaner can to back flush jet passages...

Could be timing, check all that stuff first...inside the distributor cap for deposits, the rotor for wear, bad gaskets on the carb base...but most likely it will be a worn out or damaged accelerator pump.

Pete

If the timing has changed a lot, you may have a bad distributor gear, cam gear or chain... not likely, but it could happen...

Pete
__________________
ERA 289 #2027
Reply With Quote
  #6 (permalink)  
Old 11-28-2008, 05:49 PM
Gaz64's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2008
Location: Brisbane, QLD
Cobra Make, Engine:
Posts: 2,797
Not Ranked     
Default

I run a 1405 on one of my other Holden 308s, Edelbrocks are pretty good out of the box, but like any carb will need tuning to match the needs of the engine.

Can I assume the 1806 is a AVS carb unlike the AFB style of the 1405/1406?

Have you got a "tuning kit"?

My carb is 6 years old and still has a perfect accelerator pump, maybe your carb is a little lean everywhere and now it is showing as the engine carbons up.
__________________
Gary

Gold Certified Holden Technician
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 08:04 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink