SPF Turn Signals

[maxum_101]

Hey all

my turn signals died on me.... with some help from fellow spf owners, I found it was that clear flasher thing under the dash, anyone have a part # so i can get one from Napa or some other parts place?

thanks in advance for the help

[STEVE-O]

Originally Posted by maxum_101

Hey all

my turn signals died on me.... with some help from fellow spf owners, I found it was that clear flasher thing under the dash, anyone have a part # so i can get one from Napa or some other parts place?

thanks in advance for the help

I dont have a specific part number but I belive its just the standard flasher. Just get one with the correct number of contacts.
When putting it in, loosen up the holding piece of metal a little bit so the pressure on the flasher isnt so tight.

[Blas]

Did you look on your copy of my Wiring Diagram?
All that type of information is there....

[maxum_101]

Originally Posted by Blas

Did you look on your copy of my Wiring Diagram?
All that type of information is there....

hey Blas, u see i moved 4 mnths ago and well , let just say im still unpacking.... havnt found that box with the wiring diag, haha, but i did get it all fixed up and working, 1 question tho the one i took out of the car has a diffrent part number on it from the new one i bought from the store, does that make a diffrence? the new one works fine, but i just want to make sure.

[maxum_101]

Originally Posted by STEVE-O

I dont have a specific part number but I belive its just the standard flasher. Just get one with the correct number of contacts.
When putting it in, loosen up the holding piece of metal a little bit so the pressure on the flasher isnt so tight.

hi Steve-O

thanks for your reply, it was the holding piece you mentioned that caused all the trouble, crushed the outter plastic case.

[Marvin]

The Superformance i just bought has no turn signals, what parts do i need to install them?
SPF # 2156

thanks, marvin

[Blas]

How can you not have turn signals? They were removed I assume?
Is the connector still at the base fo the steering column, just behind the dash face? Send me an email address and I'll send you a photo of the chassis plug to look for

[PANAVIA]

Classic -- I have had an issue when one bulb does bad the turn signal hangs and wont flash --

[Marvin]

Does anyone have a photo of the turn signal stalk?

I called the PO yesterday and he says never had turn signals?

thanks, marvin

[Mark IV]

Originally Posted by Marvin

Does anyone have a photo of the turn signal stalk?

http://www.autohausaz.com/vw-auto-pa...placement.html

Note that the SPF uses a connector plug on the end that VW does not. The correct unit is the "1967" one.

[Marvin]

I have that 1967 i guess but it only operates the high beam.

The lever only has two positions it feels like, there is a clear part in tray under dash that looks like a flasher?

PO that bought the car new said never has had signals or at least they did not work?

Guess i need to check further see why the switch seems to only have two positions, also it is on the right of the column, is this correct?

thanks, marvin

[Marvin]

I removed the steering wheel today.

The snap ring that holds the signal stalk was just laying there loose.

Guess I need a drawing, I think someone has had this apart or it was not assembeled correctly.

When I removed the stalk the little contact with spring fell out, I'm not sure the collar that fits inside the stalk and over the steering shaft is oeiented correctly?

And I can understand why the snapring was not in place the left side of stalk collar lacks about 1/32 going down enough to get the ring installed.

Thanks for any advice, marvin

[Blas]

You never sent me that reminder message...Check your email

[Marvin]

Thanks for the reply, will need to wait untill i get time to remove wheel again and i will take photo's.

Not sure if everything is assembeled correctly, or even if all the parts are there.

thanks, marvin