kitcarbp
Mon April 13, 2009 6:36am
Rating: 10
|
Modified Lower Radiator Hose
Here is the modified lower hose to keep the surge tank on the LOW pressure side (water pump inlet) of the system. Not the most elegant but very functional. I found a glass filled nylon "T" taht is 1.75" and has a 1.0" fill line for the surge tank.
|
|
fkemmerer
Thu May 14, 2009 6:59am
|
AFR1
Sample AFR table for an EFI FE. NOTE THAT NO ONE SHOULD COPY THIS TABLE AND JUST USE IT - THESE SETTINGS ARE NOT APPROPRIATE FOR EVERY MOTOR AND WHAT WORKS FINE IN MINE MAY VERY LIKELY DAMAGE YOURS.
|
|
fkemmerer
Thu May 28, 2009 6:05pm
|
Cranking Fuel Table for 482 ci FE with TWM Injections
Sample cranking fuel table table for an EFI FE. NOTE THAT NO ONE SHOULD COPY THIS TABLE AND JUST USE IT - THESE SETTINGS ARE NOT APPROPRIATE FOR EVERY MOTOR AND WHAT WORKS FINE IN MINE MAY VERY LIKELY DAMAGE YOURS.
|
|
Xavier
Mon July 6, 2009 2:22pm
Rating: 10
|
Fudruckers Show 2009
I won best in show at this event, I was very happy, thankful and surprised! We had a great time with great people.
|
|
Xavier
Mon July 6, 2009 2:22pm
|
Fudruckers Show 2009
I won best in show at this event, I was very happy, thankful and surprised! We had a great time with great people.
|
|
KarlCSX2498
Tue August 4, 2009 9:02am
Rating: 6
|
Fuel filler port, installed by Nick at Acton Custom
A very nice install by nick, fully TIG welded on the inside. A perfect job.
|
|
Bob In Ct
Mon September 7, 2009 7:50pm
Rating: 10
|
LRP 2009
LRP 2009 A very Nice 427 with Webers
|
|
TWOOD
Sun September 13, 2009 2:00pm
|
Trunk weather strip
Finished installation. Not very pretty, but using the larger dia. bulb wopuld not compress easily enough to permit the trunk to latch and allow the deck to be flush with the adjacent body. The original dia. weatherstrip did not compress along the top and sides at all.
|
|
Gregg(What's his name)?
Thu October 8, 2009 7:12pm
Rating: 10
|
Thursday Oct 8
Classic '65 Mustang, very close to the '66 Donna and I used to own.
|
|
fkemmerer
Thu October 8, 2009 10:31pm
Rating: 10
|
Oil Thermostat - Drivers Side 2
Completed installation of a Canton Oil Thermostat on an ERA 427SC. Note that thermostat and plumbing is not very visible to someone looking at the car from a normal angle.
|
|
Mark IV
Sun November 8, 2009 12:52pm
Rating: 10
|
The very small wheels don't handle so well.....
|
|
Z-linkCobra
Thu December 31, 2009 5:43am
|
Bottom side of block
Not a very good picture as the block is in the car currently. Here you can see the 4 bolt mains.
|
|
B&B-Cobra
Sun January 17, 2010 6:39pm
|
Cobra_8-09_027
Tackling with wiring, kit was from Haywire - very simple to use and easy instructions.
|
|
kitcarbp
Fri January 22, 2010 12:19pm
Rating: 10
|
V8 oil cooler
Ford Explorer V8 oil cooler. LONG made this OEM oil cooler for the mid 90's Explorers, if I can shoe horn this into place, it just might be the cooler I was looking for to keep the 460 oil temps uniform. This is hooked up in-line with the lower rad hose. This should have very good water flow rates to cool the oil.
|
|
FUNFER2
Sat February 6, 2010 5:46am
Rating: 10
|
Polished 304 stainless steel "Gilmore Kit". Finished.
Finished polished stainless steel side pipe. Cleaning is very easy with a quality polish. Much better than mild steel with a ceramic coating. These may last the life of the car. No glass pack to blow out. I use louvers instead. Look at the "muffler" photo.
|
|
