 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
1 |
2 |
3 |
4 |
5 |
| 6 |
7 |
8 |
9 |
10 |
11 |
12 |
| 13 |
14 |
15 |
16 |
17 |
18 |
19 |
| 20 |
21 |
22 |
23 |
24 |
25 |
26 |
| 27 |
28 |
29 |
30 |
|
|
|
|
|
CC Advertisers
|
|
|
17 result(s) to your search. (cleaned)
|
· Next Page
|
|
Bruce Edwards
Tue March 15, 2005 4:16pm
|
Bill's ERA 298 #2097 left front end 2
Another picture of the front end parts on Bill's car. Still needs to be cleaned after all of the wet sanding.
|
|
Robert Sobers
Wed November 9, 2005 10:31am
|
Shelby R Model Clone
My 66 Shelby R Clone Specs.
D.S.S. Pro Bullet 306/308 Short Block Level 10 CNC
Rods: Forgings, shot-peened, Magna Fluxed, CNC Diamond resized and fitted with ARP Wave Loc rod bolts. Balanced to racing tolerances.
Crank: Production crankshaft, thermal cleaned, shot-peened, Magna Fluxed, precision ground, oil scooped and chamfered and balanced to racing tolerances.
Pistons: DSS PRO-LITE Forged 2 valve relief flat top, CNC fly-cut for most aftermarket race cams and heads. Balanced to racing tolerances.
Rings: Sealed Power/ Speed-Pro Moly rings.
Bearings: Tri-metal rod and main bearings.
Block: 5.0 roller cam block, thermal cleaned, stress relieved, Magna Fluxed, threads chased, mains checked and corrected, oil galleys tapped for thread in plugs and the decks are CBN squared and equalized.
Transmission- C4 Automatic
Rear End- 8 Inch Detroit Locker 355 Gears.
Gt40Y Heads ported and polished.
Comp Cam by Bennett Racing Cams.
Edelbrock Air Gap Manifold
670 Holley Street Avenger Carb.
1.6 Roller Rockers
MSD Distributor
MDS 6AL Ignition Control Unit
Edelbrock Fuel Pump
Edelbrock Water Pump
AFCO Aluminum Radiator
Canton 7 QT. Oil Pan
Windage Tray
Shelby R Valve Covers with Vent Stacks
Holley Electric Fuel Pump
3/8 Stainless Fuel Line Tank to Pump
Spal Electric Fan
3 ¾ Auto-Meter Tach
Raptor LED Shift Light
Hurst Quarter Shifter with Line-Lock
K&N X-Stream Air Cleaner
Trunk Mounted Battery with Cut Off Switch
PA Performance 3-G Alt.
PA Performance Mini-Starter
Total Control Products Strut Tower Brace System
Total Control Products Sub-Frame Connectors
Auto-Power Roll Bar
Simpson Safety Harness
Hunsaker Racing Seats
Mac Headers
Mac Exhaust System with 2 ½ Inch Dumps.
R-Model Gauge Panel with 2 5/8 Autometer Gauges.
Cobra Country Oil Breather System.
|
|
Robert Sobers
Wed November 9, 2005 10:36am
|
Power Plant
D.S.S. Pro Bullet 306/308 Short Block Level 10 CNC
Rods: Forgings, shot-peened, Magna Fluxed, CNC Diamond resized and fitted with ARP Wave Loc rod bolts. Balanced to racing tolerances.
Crank: Production crankshaft, thermal cleaned, shot-peened, Magna Fluxed, precision ground, oil scooped and chamfered and balanced to racing tolerances.
Pistons: DSS PRO-LITE Forged 2 valve relief flat top, CNC fly-cut for most aftermarket race cams and heads. Balanced to racing tolerances.
Rings: Sealed Power/ Speed-Pro Moly rings.
Bearings: Tri-metal rod and main bearings.
Block: 5.0 roller cam block, thermal cleaned, stress relieved, Magna Fluxed, threads chased, mains checked and corrected, oil galleys tapped for thread in plugs and the decks are CBN squared and equalized.
|
|
blueovalfanatic
Tue September 5, 2006 1:06pm
Rating: 10
|
Paint
Heres a few things that were cleaned up and painted. Once dry and cured, everything was scuffed using a scotch-brite pad then clearcoated with Glisten PC from POR-15 to protect the paint and give it a nice shine.
|
|
LoBelly
Sun December 3, 2006 6:51am
Rating: 10
|
time to break it down
shell is cleaned up
|
|
Jackoboo
Fri December 15, 2006 9:29pm
|
DSCN02621
Cleaned engine compartment (pretty darn clean for a stock '89 302)
|
|
D&M2
Sun February 25, 2007 2:03pm
|
Chassis Prepped for Powdercoating
Finally, the chassis has been welded and prepped for sandblasting and powdercoating
|
|
RJCCOBRA
Sun December 14, 2008 1:49pm
|
Shell Valley build
The transmission has been cleaned and painted. The transmission is a close ratio, big input/big output, Ford toploader. We should be able to get the motor and transmission reinstalled in the chassis by Thursday.
|
|
hogster
Sat June 27, 2009 11:05pm
|
1.75 Inch Mild Steel tubing
cleaned up and read for fusion welding
|
|
Z-linkCobra
Mon October 19, 2009 1:58pm
|
Build pics
Machined off the riser that the stock pump bolts to across the top. Really cleaned it up I think.
|
|
DaveW
Mon May 30, 2011 12:18am
|
VZ Commodore front hubs cleaned up and clear coated
|
|
DaveW
Wed June 15, 2011 9:01pm
|
Cleaned, new seals and a paint job
|
|
dls141
Tue January 24, 2012 7:26pm
|
427SO with a new Holley HP
The engine cleaned up nicely as well. Jan 12th 2012
|
|
Dimis
Sat January 4, 2014 11:36am
Rating: 10
|
NOS Tunnel Wedge intake cleaned and coated
NOS Tunnel Wedge intake cleaned and coated
|
|
patrickt
Fri October 21, 2016 12:47pm
Rating: 10
|
|
|
All times are GMT -7. The time now is 04:58 PM.
Links monetized by VigLink |
