 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
|
|
|
1 |
2 |
| 3 |
4 |
5 |
6 |
7 |
8 |
9 |
| 10 |
11 |
12 |
13 |
14 |
15 |
16 |
| 17 |
18 |
19 |
20 |
21 |
22 |
23 |
| 24 |
25 |
26 |
27 |
28 |
29 |
30 |
|
|
CC Advertisers
|
|
 2Likes
-
1
Post By MEATMASTER
-
1
Post By STEVE-O
01-20-2020, 07:56 PM
|
 |
CC Member
|
|
|
Join Date: Oct 2003
Location: Miami,
FL
Cobra Make, Engine: Backdraft #272, 351W
Posts: 165
|
|
Not Ranked
Glass Wind Wings
Will the glass wind wings From Finish Line fit BDR? Anyone tried them?
Finish Line says they wont fit Superformance, not sure why...
Last edited by Quentin Z; 01-20-2020 at 07:59 PM..
|
01-20-2020, 08:24 PM
|
|
CC Member
|
|
|
Join Date: Dec 2015
Posts: 1,442
|
|
Not Ranked
You could ask them to lay one on their flatbed scanner. Bottom edge and both hinge points in the scanned area, and email it to you. Printing it at your end will be at 100% and give you a template to measure against yours.
I'm the guessing the SPF hinge point spacing is different.
|
01-21-2020, 08:20 AM
|
|
CC Member
|
|
|
Join Date: Oct 2003
Location: Miami,
FL
Cobra Make, Engine: Backdraft #272, 351W
Posts: 165
|
|
Not Ranked
Good idea.
|
01-21-2020, 08:58 AM
|
|
CC Member
|
|
|
Join Date: Mar 2008
Cobra Make, Engine: Johnsonville, 8-pack $4.27
Posts: 46
|
|
Not Ranked
Mounting Hole Dimensions
Here are some Superformance mounting hole dimensions to reference.
Cobra Valley's Crystal Clear Side Wind Wings
__________________
Smoke the meat, only the meat and nothing but the meat... so help me Weber
|
01-21-2020, 10:19 AM
|
|
Senile Club Cobra Member
|
|
|
Join Date: Feb 2001
Location: Buffalo, NY USA,
NY
Cobra Make, Engine: Superformance
Posts: 4,527
|
|
Not Ranked
Meat Lives!!!!
|
01-21-2020, 03:24 PM
|
 |
Backdraft Racing Dealer
|
|
|
Join Date: Dec 2004
Location: North Haven,
CT
Cobra Make, Engine: Backdraft Racing
Posts: 5,118
|
|
Not Ranked
Backdraft has unique hinge spacing. I would say no.
|
01-21-2020, 05:22 PM
|
|
CC Member
|
|
|
Join Date: Oct 2003
Location: Miami,
FL
Cobra Make, Engine: Backdraft #272, 351W
Posts: 165
|
|
Not Ranked
Thanks Jay. That’s what I was thinking.
|
01-22-2020, 07:36 AM
|
|
CC Member
|
|
|
Join Date: Feb 2008
Location: Rochester,
NY
Cobra Make, Engine: Superformance
Posts: 194
|
|
Not Ranked
Just be real careful when mounting the glass windwings. I added them thinking they would be better than getting scratches in the plastic wings. I thought I was not overtightening as recommended.
However on a drive, one of the screws must have been touching the glass straining it and on one bump, the whole thing shattered blowing glass pieces all over the interior. Quickly went back to the plastic ones and polishing as needed with Plexus products.
Last edited by STEVE-O; 01-22-2020 at 07:39 AM..
|
01-22-2020, 10:34 AM
|
|
CC Member
|
|
|
Join Date: Oct 2003
Location: Miami,
FL
Cobra Make, Engine: Backdraft #272, 351W
Posts: 165
|
|
Not Ranked
I happened to be up near Backdraft today and dropped by to see theirs. Turns out Perry had glass wings in stock at the shop, so I picked up a set. But now after reading Steve-O’s comments, I’m wondering if I should have just went with new plexi ones. Anyone have any tips on mounting the glass ones? They are countersunk on one side for the countersunk screws.
Last edited by Quentin Z; 01-22-2020 at 09:25 PM..
|
01-23-2020, 09:17 AM
|
|
CC Member
|
|
|
Join Date: Oct 2003
Location: Miami,
FL
Cobra Make, Engine: Backdraft #272, 351W
Posts: 165
|
|
Not Ranked
So, I installed the glass wings from Backdraft last night. The holes were a little off. The brackets on mine are 7 7/8" appart, and the holes in the glass wings are more like 8". I loosened everything up and got them in. I'm a little worried that there's some undue tension on the holes on the bottom driver's side, so I may go back and widen the mounting bracket holes. I did used plastic washers (made from cutting the tops off cheap drywall anchors) between the glass and all metal. No test drive yet, so I can't say if the transplant was successful. They sure do look nice though! One other note: I have the billet side-view mirrors from Breeze Automotive, so my bracket configuration is different from most but the mounting holes in the glass did line up with them.
Update: Drilled out the mounting bracket wing attachment holes a little, and everything went together much easier. All good after test drive.
Last edited by Quentin Z; 01-28-2020 at 08:29 AM..
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 03:17 PM.
Links monetized by VigLink
|
Linear Mode
